Ashly FET-1500C Şartname Sayfası - Sayfa 2

Amplifikatör Ashly FET-1500C için çevrimiçi göz atın veya pdf Şartname Sayfası indirin. Ashly FET-1500C 2 sayfaları. Ashly power amplifiers specification sheet
Ayrıca Ashly FET-1500C için: Şartname Sayfası (2 sayfalar)

Sayfayı Yazdır

ifications

Arch itect's Specif ication

Ashly Model l5O0M

The power amplifier. being oftwo channels, shall deliver a

minimum

power oI 175 watts per channel into 8 ohm

loads or 275 watts per channel into 4 ohm loads with both

channels operating. When switched into bridged mono

node. it shall deliver at least 550 watts into m 8 ohm

load. The amplifier

shall be immune

to damage from

shorted. open, or mismatched

loads. The amplifier shall

have a gain of 29dB t .5dB per channel and an input sen-

sitiviqr of 1.3 Volts ! 20/o lor lull rated output. Frequency

response shall be 10Hz Io 2OkHz t .5d8. It shall be stable

into any load including

pure capacitors and inductors.

Hum and noise shall be at least 110d8 below full output

and SMPTE intermodulation

distoftion

shall be less than

.010/o at full output. The amplifier shall have rear panel

switching for mono and bridging modes and rear mounted

level controls. The inputs shall be balanced bridging type

with male and female XLR type connectors as well as 1/4"

phone jacks. A three-color LED type indicator

shall be

employed to show the power level of each chamel and self

contained forced air cooling shall be used. The power out-

put devlces shall be of the Lateral MOS FET fpe.

The

anplifier

shall lveigh 371b. net and mount in a standard

19 inch rack using two spaces (3.5" high). The power

requirement shall be 1 10 125VAC. 50 60H2.

The porver amplitier shall be an Ashly FET- 1500M.

Ashly Model 1500C

'Ile

power amplilier, being of two channels, shall deliver a

minimum

power ol 175 watts per channel into 8 ohm

loads or 275 watis per channel into 4 ohn loads wiLh both

channcls

operating. When switched into bridged mono

mode. it shall deliver al leasi 550 watts into an 8 ohm

load. The amplifier

shnll be imntune

to dam:rge liom

shoried, open. or nisnratched loads. The amplifier shall

have a gain oi29dB t .SdB per ch:rnnel and an input sen-

sitivily of 1.3 Volts t 20/o lor ltll

rated output. F-requency

response shall be 1OLIz to 2OkHz, t .5dts. It shall be stable

inlo irny lo:rd inclllding pure capacitors and inductors.

IIum :rnd noise shall bc at lcast I 1Odts below llll output

ancl SMPI'E intermodulation clistortion shall be less than

.010/o at Iull output. Thc amplilier shall have rear panel

swikrhing lbr rrono and bridgine modes and rear ntounted

level controls. The inputs shall utilize 1/4' phonc.jacks as

well as terminal/barricr input strips. Sell conLait.red lbrced

air cooling shall be used.

'l'he

porver output dcvices shall

be ol the Lateral MOS-FET type. The nmplilier shall weigh

371b. net and mouni in a stanclard l9 inch rack usinq two

spaces (3.5' high), The power requirement shall be 110-

l2SVAC. 50-60H2.

The power amplilier shall be an Ashly FET- I 500C.

Ashly Audio Inc.

100 Fernwood Avenue

Rochester, New York 14621

ln Canada:

Gerraudio Dist

363 Adelaide Street East