Bosch CDG634A.0 Посібник користувача та інструкція з монтажу - Сторінка 9
Переглянути онлайн або завантажити pdf Посібник користувача та інструкція з монтажу для Духовка. Bosch CDG634A.0. Bosch CDG634A.0 40 сторінок.
Також для Bosch CDG634A.0: Інструкція з експлуатації (36 сторінок)
Друкувати сторінку
Setting
1
00 (softened)
01 (soft)
02 (medium)
03 (hard)
2
04 (very hard)
Only set this if you will be using solely softened water.
1
Also set for mineral water. Only use non-carbonated mineral water.
2
6.2 Initial configuration
When the appliance is connected to the power supply
for the first time or following a lengthy power failure, the
settings that you will need to configure before you can
use it will appear.
Note: You can change these settings at any time by
going to the basic settings.
→ "Basic operation", Page 9
Setting the language
Use the control ring to set the required language.
1.
Press
.
2.
a The next setting will appear.
Setting the time
Use the control ring to set the current time.
1.
Press
.
2.
a The next setting will appear.
Setting the water hardness
Use the control ring to set the water hardness
1.
range.
Press
.
2.
a This saves the water hardness range.
a A message will now appear on the display confirm-
ing that initial configuration is complete.
a The current time will be displayed.
6.3 Calibrating the appliance
The boiling point of water depends on the air pressure.
During the calibration process, the appliance adjusts to
the pressure conditions in the location where it is in-
stalled. Large amounts of steam may be generated dur-
ing the calibration process.
Running the calibration process
Notes
¡ Do not open the appliance door while calibration is
in progress as this will abort the calibration process.
¡ If you move house, restore the appliance's basic
factory settings once it is installed so that it can ad-
apt to its new location. Repeat the procedures for
initial configuration and calibration.
7 Basic operation
7.1 Switching on the appliance
Press
to switch the appliance on.
▶
a The Bosch logo will appear on the display, followed
by the heating function selection list.
Water hardness in
mmol/l
-
Up to 1.5
1.5-2.5
2.5-3.8
Over 3.8
¡ Your appliance will retain these calibration settings
Requirement: The cooking compartment is cold or at
room temperature.
1.
2.
3.
4.
5.
6.
7.
6.4 Cleaning the cooking compartment
Requirement: The cooking compartment is cold or at
room temperature.
1.
2.
3.
6.5 Cleaning the accessories
▶
7.2 Switching off the appliance
▶
a The appliance will now shut down. Any functions
German hardness °dH
-
Up to 8.4
8.4-14
14-21.3
Over 21.3
even in the event of a power failure or disconnection
from the mains. Recalibration is not necessary.
Remove the accessories and any leftover packaging
(e.g. polystyrene pellets) from the cooking compart-
ment.
Wipe the smooth surfaces in the cooking compart-
ment with a soft, damp cloth.
Press
to switch on the appliance.
Fill the water tank.
→ "Filling the water tank", Page 10
Set the required heating function, temperature and
cooking time.
→ "Setting the heating function and temperature",
Page 11
Setting
Heating function
Temperature
Cooking time
Press
to switch the appliance off.
Wait until the cooking compartment has cooled
down.
Clean the smooth surfaces with soapy water and a
dish cloth.
Empty and dry the water tank.
Dry the cooking compartment.
Clean the accessories with soapy water and a dish
cloth or soft brush.
Press
to switch the appliance off.
currently in progress will be aborted.
Basic operation en
French hardness °fH
-
Up to 15
15-25
25-38
Over 38
Value
Steam
100 °C
20 minutes
9