Alemlube G10042 Технічний посібник користувача - Сторінка 3

Переглянути онлайн або завантажити pdf Технічний посібник користувача для Інструменти Alemlube G10042. Alemlube G10042 6 сторінок. 14.4v cordless grease gun

Друкувати сторінку

OWNER'S TECHNICAL MANUAL

1. Make sure the power source voltage for connecting the battery charger is the same as that shown on the charger

specification plate. Connect thecharger to the power source.

2. Place the battery in the charger. Do not force - the slot on the battery and the charger base must be aligned.

When properly connected, the green light displays.

3. Press the SET button. The green light goes off and the red light glows, indicating that the charger is in charge mode.

4. When the battery is fully charged, the red light goes out and the green light glows. Remove the battery.

5. Disconnect the charger from the power source when not in use.

NORMAL CHARGING

Make sure power circuit voltage is the same as that shown on the charger specification plate. Connect charger to power source.

INSTALLING OR REMOVING BATTERY PACK:

Depress the two battery release buttons (one button on each side of battery pack) and pull battery pack out of grease gun.

HOW TO INSTALL A GREASE CARTRIDGE

REMOVING EMPTY GREASE CARTRIDGE

1. Pull back on the follower handle until the follower rod is fully extended and latch the follower rod groove into the slot on the tube

end cap of the Grease Tube.

2. Unscrew the grease tube assemble from the gun.

3. Carefully release the follower handle to eject the empty cartridge from container tube.

INSTALLING GREASE CARTRIDGE

1. Remove the plastic cap from the grease cartridge and insert cartridge into the container tube.

2. Remove the pull tab from grease cartridge and screw grease tube into pump assembly.

3. Release follower rod from slot to allow it to go forward. Purge air from pump. See air purging instructions.

TO CONVERT GUN TO ALLOW FILLING FROM BULK CONTAINER OR FILLER PUMP

1. Unscrew the grease tube assembly cap from the grease tube assembly. Pull on the follower handle to extract the follower

and spring from the grease tube assembly.

2. Grasp follower between thumb and forefinger and flip the follower lip from the rear to the front side.

NOTE: The follower resembles a cup. When the gun is assembled for use with bulk lubricant, the cup opens toward

the pump assembly.

3. Reassemble follower into grease tube assembly and position with the follower handle so that the grease tube assembly

cap can be tightened onto the container tube.

TO FILL THE GUN FROM BULK CONTAINER

1. Remove grease tube from the gun.

2. Insert the open end of the grease tube assembly into lubricant. Slowly pull the follower handle back while pushing the grease

tube assembly deeper into the lubricant to prevent air pockets from being pulled into the grease tube assembly.

3. When the follower rod is fully extended, pull it sideways to latch the rod groove into the keyhole slot in the grease tube

assembly cap.

4. Turn the Grease Tube into the gun and release the follower rod from the slot on the end cap of the tube to allow the follower

rod go forward.

5. Clean any excess grease of the gun body.

NSW/ACT

QLD/PNG

TEL: (02) 9677 1555

TEL: (07) 3204 9166

FAX: (02) 9675 1155

FAX: (07) 3204 1224

14.4V Cordless Grease Gun

VIC/TAS

TEL: (03) 8787 8288

FAX: (03) 8787 8266

Visit our website at

www.alemlube.com.au

SA/NT

TEL: (08) 9302 4199

TEL: (08) 8241 7111

FAX: (08) 9303 2095

FAX: (08) 8241 7011

www.alemlube.co.nz

G10042

TEL: (09) 447 1007

FAX: (09) 447 1008