Bosch Uneo Maxx Оригінальна інструкція з експлуатації - Сторінка 9
Переглянути онлайн або завантажити pdf Оригінальна інструкція з експлуатації для Електроінструмент Bosch Uneo Maxx. Bosch Uneo Maxx 18 сторінок. Cordless rotary hammer
Також для Bosch Uneo Maxx: Оригінальна інструкція з експлуатації (11 сторінок)
Друкувати сторінку
Setting the rotational direction (see figure G)
Only operate the rotational direction switch (7) when
u
the power tool is not in use.
The rotational direction switch (7) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (8) is being pressed.
– Right rotation: To drill and to drive in screws, press the
rotational direction switch (7) through to the left stop.
The rotational direction indicator for right rotation
(5) lights up when the on/off switch (8) is pressed
and the motor is running.
– Left rotation: To loosen and unscrew screws and nuts,
press the rotational direction switch (7) through to the
right stop.
The rotational direction indicator for left rotation
(6) lights up when the on/off switch (8) is pressed
and the motor is running.
Switching On/Off
– To start the power tool, press and hold the on/off switch
(8).
The lamp (11) lights up when the on/off switch (8) is lightly
or fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
– To switch off the power tool, release the on/off switch
(8).
At low temperatures, the power tool will take a certain
amount of time to reach its full hammer/impact perform-
ance.
Adjusting the Speed/Impact Rate
You can adjust the speed/impact rate of the power tool when
it is on by pressing in the on/off switch (8) to varying ex-
tents.
Applying light pressure to the on/off switch (8) results in a
low rotational speed/impact rate. Applying increasing pres-
sure to the switch increases the speed/impact rate.
Run-out brake
Upon releasing the on/off switch (8), the drill chuck is
slowed down, which prevents the application tool from con-
tinuing to rotate.
When driving in screws, you should therefore only release
the on/off switch (8) once the screw has been inserted flush
into the workpiece. This way, the head of screw will not pen-
etrate the workpiece.
Battery Charge Indicator
When the on/off switch (8) is pressed in halfway or com-
pletely, the battery charge indicator (9) indicates the bat-
tery's state of charge for several seconds. The indicator con-
sists of three green LEDs.
LED
Continuous light 3 x green
Continuous light 2 x green
Continuous light 1 x green
Bosch Power Tools
LED
Slowly flashing light 1 x green
The three LEDs of the battery charge indicator (9) and the
lamp (11) flash quickly when the temperature of the battery
falls or rises outside the operating temperature range of –20
to +50 °C.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or not kept within the
permitted battery temperature range, the power output is
reduced or the power tool is switched off. The power tool
will not run at full power output again until the permitted bat-
tery temperature has been reached.
The three LEDs in the battery charge indicator (9) and the
lamp (11) flash quickly when the temperature of the battery
is outside the operating temperature range of –20 to +50 °C
and/or the overload protection has been triggered.
Protection against deep discharge
The lithium-ion battery is protected against deep discharge
by the Electronic Cell Protection (ECP). When the battery is
discharged, the power tool is switched off by means of a pro-
tective circuit: The application tool no longer rotates.
Practical Advice
Only apply the power tool to the screw/nut when the
u
tool is switched off. Rotating tool inserts can slip off.
Maintenance and Servicing
Maintenance and Cleaning
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Replace a damaged dust protection cap immediately.
u
It is recommended that you have use an after-sales
service for this.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
After-sales service and advice on using products
Our after-sales service can answer questions concerning
product maintenance and repair, as well as spare parts. You
can find exploded drawings and information on spare parts
at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
Capacity
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the type plate of
≥ 67%
the product.
34–66%
Great Britain
11–33%
English | 9
Capacity
≤ 10%
1 609 92A 4KJ | (25.07.2018)