AirTech UM-14001-20627 Посібник користувача - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник користувача для Іграшка AirTech UM-14001-20627. AirTech UM-14001-20627 5 сторінок. Radio-controlled airship

Друкувати сторінку

• The manufacturer is not responsible for any loss or damage caused by unsafe

operation of the blimp. Always use common sense when piloting your blimp!

• The gondola should be handled carefully. It is made of lightweight

• Hold the balloon securely after filling it with Helium to prevent it from flying away!

• Do not continue to fill the balloon after it becomes firm - it could burst.

• The balloon expands when temperature rises. If you completely fill the balloon at a low

temperature and the room temperature increases, the balloon may rupture or burst.

Your kit includes:

1. Metallized inflatable balloon

2. Gondola (thruster module)

3. Transmitter with antenna

4. Putty (for balancing/ballast)

5. Rudder fins

You also need (not included):

1. 1 Battery CR123A (3V Lithium battery) for the gondola.

2. 1 Battery 6F22 (9V Alkaline battery) for the transmitter.

3. Helium gas for the balloon (available from florists, party shops, or any

other shop selling balloons).

4. Single and double sided-tape to attach gondola and fins to balloon.

Install Batteries

Open

the

gondola's

compartment by removing the screw

from the battery compartment's door.

Insert a CR123A lithium battery into

the battery holder, ensuring that the

polarity is correct. Close the battery

compartment and tighten the screw.

Remove the battery cover located at the

rear of the transmitter by sliding it

downwards. Insert a 9V alkaline battery into

the battery compartment, again being careful

to position it so that the polarity is correct.

Fill Balloon with Helium

Insert the helium tank nozzle into the Auto-Seal Valve, which is located

within the flap on the seam of the balloon. Gently

push the nozzle into the opening - be careful not to

push the nozzle too far as it may damage the

balloon's Auto-Seal Valve. Fill the balloon with

Helium until the balloon becomes firm, without

over-stressing the seams. Remove the filler nozzle

then close the auto-seal valve by pressing the

Auto-Seal Valve back together. Note that you can

roll the flap up and tape it in position to minimize

any chance of Helium leaking out.

Connect the Gondola (Thruster Module)

Apply double-sided tape to the inside bottom of the gondola, around the

flat outer area or by which the gondola will be attached to the balloon.

Secure the module to the underside of the blimp. You may find it easiest

to hold the helium-filled airship with one arm while pressing the taped

Warnings & Safety Precautions!

• This airship is designed for indoor use only!

materials that can be easily damaged by rough handling.

battery

module to the bottom center of

the balloon with the other

hand. Another option is to

allow the balloon to rise to the

ceiling and then attach the

gondola from the underside.

Once the module is attached,

apply single-sided tape around

the outside lip to ensure maximum adhesion.

Note that the On/Off switch of the gondola should face the rear of the

balloon.

Uncoil the antenna wire and let it trail from the rear of the module -

away from the propellers.

NOTE: Placing the module in the position required for proper balance

may take a few attempts. You can remove and reposition the module by

carefully peeling it away from the balloon. Notice how the balloon reacts

with

the

weight

gondola. If it is nose-heavy

then

move

slightly

backward. If it is tail-heavy

then try moving it slightly

toward the front of the

balloon. Make sure the module

is aligned straight along the

axis of the balloon!

Install the Styrofoam Fins

Carefully separate the die-cut styrofoam sheet into 4 fins by following

the perforated lines. Each fin has one edge with tabs that need to be

separated. Bend each tab 90° -

The first tab to the left and the

next to the right, continuing to

alternate to the end .

Attach the fins to the rear of

the Blimp by using double-

sided tape or regular Scotch

tape. Ensure that the fins are

straight!

Ballast the Balloon

The blimp must be adjusted so that it is neutrally buoyant. This is

merely a fancy way of saying that the blimp must float at about eye-level

without rising or falling. This is accomplished by adding the correct

amount of 'ballast' putty. Note that the bombs and battery must already

be installed at this point (see next page).

the

UM-14001-20627