Ansa RS-1 Посібник з монтажу та експлуатації - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник з монтажу та експлуатації для Блок управління Ansa RS-1. Ansa RS-1 12 сторінок. Ansa roller door remote control unit

Друкувати сторінку
Ansa RS-1 Посібник з монтажу та експлуатації
2.3 Receiver Unit
The Receiver Unit has a built-in Control button which functions in the same way
·
as the Keyfob Transmitter button.
The Receiver has a built on courtesy light which will switch on for 3½ minutes
·
whenever the door is operated and turn off automatically.
The receiver mounted red LED is a multifunction indication light, flashing rapidly
·
when the photocell or light grid system is blocked and flashing slowly for fault
detection.
2.4 Hold To Run Close Facility
Hold to run is also a control option for doors not requiring photoelectric cell or light grid
safety system
Alternatively,
System is obstructed or malfunctions (indicated by a rapidly flashing red LED) and the door
will not close. Please use the following procedure - ensuring that the door is in full view.
Press the keyfob operation button or RS1 operation button for one second to
·
open the door or stop an opening door.
To close the door - press and hold a button continuously and after 5 seconds the
·
door will start to close. Closure is only possible if the button is held continuously and
it will stop if the button is released, requiring the full sequence to be repeated.
Please note - Do not use the Hold To Run facility if the red LED indicator is on constant.
3.5 Using Additional Access Controls
Enter a 4 digit personal
access code to operate
your door.
Weatherproof high security
unit with key illumination
suitable for installation
outside the garage.
Figure 4
DK-14 Wireless
Code Switch

3 - Fitting the RS-1 Control Unit

The RS1 control unit is normally fitted on the same side as the motor
3.1
drive. Select a suitable position for the control unit, within sight of the door,
well away from moving parts, ensuring that:-
a.
It can be plugged into an adjacent 13A switched socket.
b.
It is within the constraints of the motor lead, using a 'tidy' cable run.
c.
It is mounted with the built on lamp at the top.
It is fitted at a height of at least 1.6 metres out of the reach of children.
d.
e.
It is fitted inside a dry room only ( I.P .44 rating )
3.2
Fitting the enclosure - Refer to fig 5
Remove the courtesy lamp lens from the base by squeezing the sides of the
lens, disengaging the clip in the top of the lens. Remove any packaging from
the lamp. Pull off the trim, and undo the two fixing screws approximately
15mm, noting that it is not necessary to completely remove the screws
which remain attached to the cover. Carefully remove the cover by pulling
away from the base with a slight downward movement. The packing box lid
provides a useful drill fixing template. Fix the base to the wall using the fixing
screws and plugs provided.
Note: Do not allow dust to enter the unit which could damage the
electronics.
Page 2
in the event that the optional Photoelectric Beam or Light Grid
Ultra secure key
operation for your
door.
Weatherproof high
security unit with blue
LED indicator suitable
for installation outside
Figure 5
the garage
WK-1 Wireless
Key Switch
BASE
Courtesy Light
To control the door
from an alternative
position within the
garage.
One, two or three
channel versions
are available.
Figure 6
WB-1 Wireless
Wall Button
BUILT -ON LIGHT
MULTI-FUNCTION
RED LED INDICATOR
OPERATING BUTTON
COVER SCREWS
AERIAL
RS1
Control
Button
Red LED
Indicator
Figure 3
LUGS
COVER
SPARE MAIN
BOARD FUSES
TRIM
Figure 7