Gage Bilt GB713 Посібник з монтажу - Сторінка 6

Переглянути онлайн або завантажити pdf Посібник з монтажу для Інструменти Gage Bilt GB713. Gage Bilt GB713 14 сторінок.
Також для Gage Bilt GB713: Оригінальна інструкція з експлуатації (18 сторінок), Оригінальна інструкція з експлуатації (20 сторінок)

Друкувати сторінку

DESCRIPTION

WARNING:

The balance of the tool is designed for horizontal use and is not suited for any other application. Gage Bilt will

be pleased to advise for your specific application.

The GB713 is a pneumatic-hydraulic tool designed specifically for the efficient installation of a wide range of blind rivets. It weighs

6.50 lbs. (2.9 kg) and can be operated in any position with one hand. It has a .760" (19.3 mm) rivet setting stroke and a rated pull load

of 4,500 lbs. (20.0 kN) with 90 psi (6.2 bar) air pressure at the air inlet.

The GB713 riveter operates on a wide range of air pressure, with 90 to 100 psi (6.2-6.9 bar) providing the maximum efficiency. At 90

psi (6.2 bar) air pressure, the GB713 does not exceed 81.5 dB (A) and consumes 3 cfm at 20 cycles a minute.

The air inlet is provided with 1/4-18 female pipe threads to accept the users air hose fitting.

NOSE ASSEMBLIES ARE NOT FURNISHED WITH TOOL AND MUST BE ORDERED SEPARATELY. (See page 13 for nose assembly

recommendations.)

MAINTENANCE

WARNING:

Maintenance personnel

WARNING:

Disconnect tool from its power source before performing maintenance.

WARNING:

Excessive contact with hydraulic oil and lubricants should be avoided.

WARNING:

Dispose of Hydraulic Oil in accordance with all environmental regulations applicable in your area.

WARNING:

Read MSDS documents for all applicable materials.

The performance of any tool depends upon good maintenance practices. Following these minimal requirements for service and care

will extend the life of your tool.

*Only use an air supply set at 90-100 psi (6.2-6.9 bar) equipped with a filter-regulator to prevent wear.

*The tool will eventually lose some hydraulic oil. Keep the hydraulic system full (only use Dexron III, or equivalent) and free of air by

using the fill bottle assy (745163) on a weekly basis.

*Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all applicable

tool manuals and nose assembly data sheets prior to operating tools.

*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces that jaws ride on with

light machine oil on a daily basis.

*All Screwed End Caps, Base Covers, Air Fittings, Actuators, Screws and Nose Assemblies are to be examined at the

end of each working shift to check that they are secure.

*Check tool, all hoses and all couplings daily for damage or air/hydraulic leaks. Tighten or replace (if necessary).

*For a complete overhaul, tool kit (GB740TK) is recommended.

CLEANING AND LUBRICATING PROCEDURE

Daily cleaning and lubrication of nose assembly will greatly reduce downtime and

increase life of components. Using sewing machine oil, or an equivalent cleaner/

lubricant, follow instructions below.

1. Disconnect tool vacuum line (if equipped).

2. Point nose assembly into oil as shown.

3. Cycle tool 8-10 times and wipe dry.

TORQUE SPECIFICATIONS

Button Head Cap Screws (402479) = 40 inch lbs.

Packing Plug (744118) = 45 foot lbs.

Flexlock Nut (400559) = 40 inch lbs.

End Cap (713217) = 45 foot lbs.

Button Head Cap Screws (402482) = 35-40 inch lbs. (Do NOT over-tighten)

MUST

read and understand all warnings and cautions.

Image may not

reflect actual tool

7/11 REV 10/14