AutomationDirect DURApulse GS20 Посібник із швидкого старту

Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Приводи постійного струму AutomationDirect DURApulse GS20. AutomationDirect DURApulse GS20 8 сторінок.

Друкувати сторінку

DURApulse GS20 AC Drive Quick-Start Guide

GS20 AC Drives Installation Instructions

Sensorless Vector Control Variable Frequency Micro-drive

• Please read this instruction sheet thoroughly before installation and retain for later

reference.

• To ensure the safety of operators and equipment, only qualified personnel familiar

with AC drives should install, wire, program, and operate the GS20 drive. Always read this instruction sheet

thoroughly before using the GS20 drive, especially the WARNING, DANGER and CAUTION notes. If you have any

questions, please contact AutomationDirect.

PLEASE READ PRIOR TO INSTALLATION FOR SAFETY

• The ground terminal of the GS20 drive must be grounded correctly. The grounding method

must comply with the laws of the country where the GS20 drive is to be installed.

• After power has been turned off, the capacitors in the GS20 drive may retain a charge for

several minutes. To prevent personal injury, visually verify that the "CHARGE" LED has

turned off. Then measure to confirm that the DC bus voltage level between terminals (+1)

and (-) is less than 25VDC before touching any terminals. (Capacitor discharge will take at

least 5 minutes for most GS20 models)

• The CMOS ICs on the internal circuit boards of the GS20 drive are sensitive to static

electricity. Please DO NOT touch the circuit boards with your bare hands before taking

anti-static measures. Never disassemble the internal components or circuits.

DANGER

• If wiring changes must be made, turn off power to the GS20 drive before making those

changes. Allow the internal DC bus capacitors in the GS20 drive sufficient time to discharge

prior to making changes in power or control wiring. Failure to do so may result in short

circuit and fire. To ensure personal safety, allow DC bus voltage to discharge to a safe level

before making wiring changes to the GS20 drive.

• DO NOT install the GS20 drive in locations subject to high temperature, direct sunlight, or

flammable materials.

• Never apply power to the output terminals U/T1, V/T2, W/T3 of the GS20 drive. If a fault

occurs during operation of the GS20 drive, refer to the fault code descriptions and corrective

actions to reset the fault before attempting to operate the GS20 drive.

• DO NOT use Hi-pot test for internal components. The semi-conductors in the GS20 drive are

WARNING

easily damaged by high voltage.

• Long motor lead lengths may result in reflective wave due to impedance mismatch between

the motor cable and the motor. Reflective wave may damage the insulation of the motor.

To avoid the possibility of reflective wave damage, use an inverter-rated motor with an

insulation rating of 1600 volts. A load reactor installed between the GS20 drive and motor

will help to mitigate reflective wave.

• Nominal supply voltage to the GS20 drive should be less than or equal to 120/240/480 volts

AC depending on GS20 model.

• Nominal supply current capacity should be less than or equal to 100kA for all GS20 models.

• The GS20 drive must be installed in a clean, well-ventilated and dry location, free from

corrosive gases or liquids.

CAUTION

• The GS20 drive must be stored within an ambient temperature range from –40°C to +85°C,

and relative humidity range of 0% to 90% without condensation.

• Do not apply AC power to the GS20 drive with the front cover removed. Following a fault of

the GS20 drive, wait 5 seconds before pressing the RESET key.

• To improve power factor, install a line reactor ahead of the GS20 drive. Do not install power

correction capacitors in the main AC supply circuit to the GS20 drive to prevent drive faults

due to over-current.

Minimum Wiring

• AC input power to R/L1, S/L2, T/L3 (for single-phase input, use two of the terminals) (For applicability of 1-phase

input power, please refer to Chapter 1 of the DURApulse GS20 AC Drives User Manual at AutomationDirect.com.)

• Ground from the power supply

• Drive power to the motor (U, V, W on T1, T2, T3) (For use with 3-phase motors only!)

• Ground to the motor

• STO1 and STO2 (both must be wired through appropriate N.C. safety-rated contacts to DCM or the

factory-installed jumpers must be left in place)

With this minimal wiring, the drive can be operated via the keypad to test the motor and drive installation.

See the "Parameter Set Up"

(page

4) section to configure the drive for keypad operation.

Recommended Safety Wiring

We strongly recommend that customers use the STO safety feature.

The Safe Torque Off (STO) function turns off the power supplied to the motor through the hardware, so

that the motor cannot produce torque. This method of removing power from the motor is considered an

emergency stop, also known as "coast to stop."

To use this feature, disconnect the appropriate factory-installed jumpers and wire a safety relay or safety PLC

as shown. The E-Stop pushbutton should be wired through a Safety Relay or PLC to meet Category 3 safety

requirements. See User Manual Appendix E for wiring the GS20 with STO.

GS20_QSP 1st Edition, Rev C 03/03/2022

Wiring Diagrams

RFI Jumper Removal

If the power distribution system supplying the GS20 AC drive is a floating (IT) or an

asymmetric ground system (including most 120V inputs), the RFI jumper must be

removed.

Removing the RFI jumper uncouples the internal RFI capacitor (filter capacitor)

between the GS20 drive frame and circuitry to avoid damaging those circuits and

(according to IEC 61800-3) to reduce ground leakage current.

GS20 Frame A through F

Note: Remove Clip

Main Wiring (Power Circuit)

For main (power) wiring terminal specifications, Please refer to "Specifications for Wiring Terminals –

Main-Circuit Terminals"

(page

2).

GS20 all Frames

*(Note that 1-phase drives do not have a T/L3 terminal. 120V drives do not have DC- and DC+ terminals.)

DC reactor (optional)

Input: one-phase / three-phase* power

Jumper

Circuit Breaker or Fuse

R/L1

S/L2

T/L3*

It is recommended that

R1C

you install a protective

circuit at R1C – R1 to

protect the drive from

OFF

damage.

When a fault occurs, the MC contactor

switches to OFF to shut off the drive input

power and protect the power system.

R1C and R1 are the relay output terminals.

GS20 Control Terminal Wiring

(See page 2 for Start/Stop wiring options)

Default functions

set via Parameters

P02.00 - P02.07

NOT E

*DI7 can input 33 kHz pulses.

*Do NOT apply the mains voltage directly to

external terminals.

Default:

NPN (SINK) Mode (internal power)

Please refer to the wiring of NPN mode and PNP mode.

N OT E

It is a short circuiting jumper installed between

+24 V, S1 and S2 short when GS20 leaves the factory.

Remove this short circuiting jumper before using the

safety function while wiring.

2: The +24 V is for STO only, and cannot be used for any

other purpose.

E STOP

Safety PLC

or Relay

See User Manual Appendix E for

more information

5KΩ

Functions set via Parameters

P03.00 and P03.01

Main circuit terminals

Control terminals

Shielded leads & Cable

Brake resistor (optional)

Motor

U/T1

V/T2

W/T3

FWD (DI1)

DURApulse GS20 AC Drive Quick-Start Guide – 1st Ed, Rev C 03/03/2022

Functions set via Parameter P02.13

+24 V

R1O

Multi-function relay output terminals

+24 V

250 VAC / 3 A (N.O.)

FWD/STOP

R1C

DI1/FWD

250 VAC / 3 A (N.C.)

REV/STOP

DI2/REV

Inductive Load (COS 0.4)

Multi-step speed 1

250 VAC / 1.2 A

DI3

Multi-step speed 2

DI4

Multi-step speed 3

DI5

Multi-step speed 4

Functions set via Parameters P02.16 and P02.17

DI6

N/A

DI7

Multi-function output

Digital Signal Common

DCM

frequency terminals

30 VDC / 30 mA 33 kHz

DCM

NPN

Multi-function output

DO1

terminal 48 VDC / 50 mA

Multi-function output

DO2

terminal 48 VDC / 50 mA

Multi-function output

DOC

common terminal (photocoupler)

See User Manual Appendix D for

sink/source wiring examples

+24 VDC

Analog Multi-function output

AO1

terminal 0 – 10 VDC /

0 – 20 mA / 4 – 20 mA

Analog Signal common

SCM

- 1

* 1

Functions set via Parameter P03.20

+24 V

AO1

AFM

STO1

STO2

SGND

SG+

Modbus RS-485

+10 VDC / 20 mA

+ 10 V

0 – 10 VDC

AI1

-10 VDC – 10 VDC

- 2

0 – 20 mA / 4 – 20 mA

0 – 20 mA

4 – 20 mA

AI2

Communication card/

0 – 10 VDC

AI2

ACI

Option Slot

DC 24V external power supply card

Analog Signal common

ACM

USB Port

FWD (DI1)

REV (DI2)

DI7

FWD (DI1)

REV (DI2)

DI7

Page 1