ADEMCO Quest 2260SN Інструкція з монтажу - Сторінка 4

Переглянути онлайн або завантажити pdf Інструкція з монтажу для Аксесуари ADEMCO Quest 2260SN. ADEMCO Quest 2260SN 4 сторінки. Microwave/pir polling loop motion sensor

Друкувати сторінку

SUPERVISION

This motion sensor is equipped with advanced supervision of both

the PIR and microwave channels. If a microwave channel failure

occurs, the sensor will continue to operate as a dual-element PIR

sensor (when DIP switch #1 is set to ON) in Standard Signal

Processing mode regardless of the processing option chosen. Even

though some operation is maintained, the unit should be replaced

as soon as possible. If a PIR failure occurs, the unit becomes non-

operational.

Supervision Failure Indications

If a supervision failure occurs, it will be indicated by the

appropriate LED flashing once every 3 seconds, provided the LED

enable option was chosen by DIP switch #3. If a PIR failure occurs,

the RED LED will flash; if a microwave failure occurs, the GREEN

LED will flash. If the unit has defaulted to PIR-only operation as a

result of a microwave failure (DIP switch #1 is set to ON), the RED

LED will light when an alarm occurs while the GREEN LED

continues to flash.

All troubles above will be reported to the control panel.

MAINTAINING PROPER OPERATION

In order to maintain the detector in proper working condition, it is

important that the user observe the following:

1. Power should be provided at all times. Loss of power to the unit

will result in the alarm contacts reverting to an alarm state.

The units DC source should have standby power available for at

least 4 hours of operation during emergencies.

2. Units should never be re-aimed or relocated without the advice

or assistance of the alarm service company.

3. The physical surroundings of the protected area should not be

changed. If furniture or stock is moved, or air conditioning or

additional heating is installed, the system may have to be

readjusted by the alarm service company.

4. Walk tests should be conducted frequently (at least weekly) to

confirm proper coverage by each detector.

TO THE INSTALLER

Regular maintenance and inspection (at least annually) by the

installer and frequent testing by the user are vital to continuous

satisfactory operation of any alarm system.

The installer should assume the responsibility of developing and

offering a regular maintenance program to the user, as well as

acquainting the user with the proper operation and limitations of

the alarm system and its component parts.

Recommendations must be included for a specific program of

frequent testing (at least weekly) to ensure the system's operation

at all times.

FEDERAL COMMUNICATIONS COMMISSION

(FCC) STATEMENT

This device complies with Part 15 of FCC Rules. Operation is

subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including

interference that may cause undesired operation.

165 Eileen Way, Syosset, New York 11791

K5510 12/00

WARNING! THE LIMITATIONS OF YOUR

MICROWAVE/PASSlVE INFRARED MOTION DETECTOR

While the Intrusion Detector is a highly reliable intrusion detection device, it does not

offer guaranteed protection against burglary. Any Intrusion Detection device is

subject to compromise or failure to warn for a variety of reasons:

• These Motion Detectors can only detect intrusion within the designed ranges as

diagrammed in this installation manual.

• The passive infrared motion sensor in this Motion Detector does not provide

volumetric area protection. It does create multiple beams of protection, and

intrusion can only be detected in unobstructed areas covered by those beams.

• Passive Infrared Detectors cannot detect motion or intrusion that takes place

behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or

windows.

• Metal objects (or other reflectors, such as foil faced insulation or water in bottles)

can alter the microwave sensors protection pattern.

• Mechanical tampering, masking, painting or spraying of any material on the

mirrors, windows or any part of the optical system can reduce the detection ability

of the Passive Infrared Motion Detector.

• Passive Infrared Detectors sense changes in temperature; however, as the ambient

temperature of the protected area approaches the temperature range of 90° to

105°F (32° to 40°C), the detection performance can decrease.

• This Passive Infrared Detector will not operate without appropriate DC power

connected to it or if the DC power is improperly connected (i.e. reversed polarity

connections).

• Passive Infrared Detectors, like other electrical devices, are subject to component

failure. Even though they are designed to last as long as 10 years, the electronic

components could fail at any time.

We have cited some of the most common reasons that a Passive Infrared Motion

Detector can fail to catch intrusion. However, this does not imply that these are the

only reasons and therefore, it is recommended that weekly testing of this type of unit,

in conjunction with weekly testing of the entire alarm system, be performed to ensure

that the detectors are working properly.

Installing an alarm system may make the owner eligible for a lower insurance rate,

but an alarm system is not a substitute for insurance. Homeowners, property owners

and renters should continue to act prudently in protecting themselves and continue to

insure their lives and property.

We continue to develop new and improved protection devices. Users of alarm systems

owe it to themselves and their loved ones to learn about these developments.

ADEMCO Limited Warranty

Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its

divisions, subsidiaries and affiliates ("Seller"), 165 Eileen Way, Syosset, New York

11791, warrants this detector to be in conformance with its own plans and

specifications and to be free from defects in materials and workmanship under

normal use and service for 36 months from the date stamp control on the product.

Seller's obligation shall be limited to replacing, at its option, free of charge for

materials or labor, a detector which is proved not in compliance with Seller's

specifications or proves defective in materials or workmanship under normal use and

service. Seller shall have no obligation under this Limited Warranty or otherwise if

the detector is altered or improperly repaired or serviced by anyone other than

Ademco factory service. In case of defect, return the detector to ADI or an authorized

distributor for an immediate replacement.

THERE

ARE

WARRANTIES,

MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR

OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE

HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY

CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY

OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF

LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY

THE SELLER'S OWN NEGLIGENCE OR FAULT.

Seller does not represent that its detector may not be compromised or circumvented;

that the detector will prevent any personal injury or property loss by burglary,

robbery, fire or otherwise; or that the detector will in all cases provide adequate

warning or protection. Buyer understands that a properly installed and maintained

alarm may only reduce the risk of a burglary, robbery, fire or other events occurring

without providing an alarm, but it is not insurance or a guarantee that such will not

occur or that there will be no personal injury or property loss as a result.

CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL

INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE

DETECTOR FAILED TO GIVE WARNING. However, if Seller is held liable, whether

directly or indirectly, for any loss or damage arising under this Limited Warranty or

otherwise, regardless of cause or origin, Seller's maximum liability shall not in any

case exceed the purchase price of the DETECTOR, which shall be the complete and

exclusive remedy against Seller. This warranty replaces any previous warranties and

is the only warranty made by Seller on this detector. No increase or alteration,

written or verbal, of the obligations of this Limited Warranty is authorized.

EXPRESS

IMPLIED,