Airflow SunShine 6600ATP Інструкція з електромонтажу для електриків - Сторінка 2
Переглянути онлайн або завантажити pdf Інструкція з електромонтажу для електриків для Обігрівач Airflow SunShine 6600ATP. Airflow SunShine 6600ATP 2 сторінки.
Друкувати сторінку
Thank you for purchasing this quality
Sunshine Radiant Globe Heater. The
Sunshine Range is made in Australia for
Australian homes and includes a 5 year in
home warranty with a 2 year replacement
warranty on the heat globes.
Before attempting to install this unit, please
read the following instructions carefully.
Installing your Sunshine Heater according to
these directions will ensure years of trouble-
free operation.
This unit can be mounted in any room that
requires direct, radiant heat at the flick of a
switch. These instructions suit Model Number:
6600ATP En Suite Radiant Heater, Light and
Exhaust Fan
1 1 1 1 1
2 2 2 2 2
MOUNTING
1. Using this card in its open state as a template, position it on the area of the ceiling where you
want to install your Sunshine. Draw around the edges of the template with a pencil to mark
the hole cutting size. Be sure to check above the ceiling for minimum space of 280mm
and the location of the ceiling joists.
2. Using a saw, cut out the section along the drawn lines.
3. Insert your Sunshine into the hole, making sure to pull the two side springs inwards so that
the body can pass through the hole without damaging the plaster. Once fully inserted, the
springs must be returned to their original position. The body is now securely fixed in the
ceiling.
Note: Springs can be adjusted to suit either 10mm or 13mm plasterboard ceilings.
Alternatively, the unit can be fixed into position via the four holes in the body flange.
4. The lamp surround has been designed to position heat globes correctly in the main body.
Clip the ceiling cowl to the body, making sure all four clips snap into place. Failure to position
lamp surround correctly may cause heat globes to touch the main body and cause warping.
5. Screw the two R63 60 watt (small) light globes into place. Screw the two large heat globes
through the cowl holes and into the body mounted sockets. The globes should be screwed in
firmly, but not over tightened, to ensure a good electrical contact.
CLEANING
•
Remove heat globes when at room temperature. Wipe with a damp cloth, never immerse.
•
Unclip ceiling cowl and wash in warm soapy water. Always use a soft cloth, never abrasives.
•
Clean away any excess fluff from inside the body, motor/blade brackets.
SPARE PARTS
Electrical switches are available from any electrical
wholesaler. The central light globes (small) should be
replaced by pearl R63 60 watt lamps, Par t No. 6630-LP.
The special Hard Glass radiant heat globes are only
available from selected retailers and wholesalers,
Part No. 6500C.
Note: Maximum wattage of small centre globes is
60 watts.
IMPORTANT
THIS CARD IS ALSO YOUR
INSTALLATION TEMPLATE
FITTING INSTRUCTIONS
3 3 3 3 3
F1671/01
SUITABLE LOCATIONS
To achieve the most effective heating from
the Sunshine's infra-red radiant heat globes,
the unit must be positioned directly over the
area requiring warmth.
Sunshine heaters are designed for cavity
type ceilings. Flat roof installation in NOT
recommended unless an additional flue is
installed to exhaust outside.
Before you start fitting the unit, make sure
your ceiling has at least 280mm clearance
from the roof. This unit must not be mounted
in areas that are subject to direct splashing.
The Sunshine En Suite must be mounted in
the horizontal position only and is not
suitable for 'cathedral' or 'raked' ceilings.
4 4 4 4 4
5 5 5 5 5