HIKVISION DS-7716NI-I4/16P Посібник із швидкого старту
Переглянути онлайн або завантажити pdf Посібник із швидкого старту для ВІДЕОРЕЄСТРАТОР HIKVISION DS-7716NI-I4/16P. HIKVISION DS-7716NI-I4/16P 2 сторінки.
Також для HIKVISION DS-7716NI-I4/16P: Посібник із швидкого старту (17 сторінок)
Друкувати сторінку
DS-7716NI-I4/16P NVR Quick Start Guide (QSG)
© 2017 Hikvision USA Inc. • All Rights Reserved • Any and all information, including, among others, wordings, pictures, and graphs are the properties of Hangzhou Hikvision Digital
Technology Co., Ltd., or its subsidiaries (hereinafter referred to as "Hikvision").
This user manual (hereinafter referred to as "the Manual") cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written
permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees, or representations, express or implied, regarding the Manual.
About this Manual: The Manual includes instructions for using and managing the product. Pictures, charts, images, and all other information hereinafter are for description and
explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version on the company
Website (http://www.hikvision.com/us). Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement:
and other Hikvision trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos
mentioned below are the properties of their respective owners.
Legal Disclaimer: TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE, AND FIRMWARE, IS
PROVIDED "AS IS," WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING,
AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE
OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY
RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE, OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS
INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT
YOUR USE CONFORMS TO THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED FOR ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information
FCC Information
FCC Compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.
This device may not cause harmful interference.
2.
This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and, if applicable, the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under
the EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE Directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return
this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see:
www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this symbol,which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance: This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Safety Instruction: These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into
"Warnings" and "Cautions."
•
Warnings: Serious injury or death may occur if any of the warnings are neglected.
•
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Warnings Follow these safeguards to prevent serious injury or death.
Cautions Follow these precautions to prevent potential injury or material
damage.
Warnings
•
Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.
•
In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Refer to technical specifications for detailed information.
•
Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Refer to
technical specifications for detailed information.
•
Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard.
•
Make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed.
•
If smoke, odor, or noise rise from the device, turn off the power at once and unplug the power cable, and then contact the service center.
Cautions
•
Make sure the power supply voltage is correct before using the device.
•
Do not drop the device or subject it to physical shock.
•
If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the device will not be used for an extended period, protect it from dirt.
•
Do not place the device in extremely hot, cold, dusty, or damp locations, and do not expose it to high electromagnetic radiation. Do not operate product in outside of its stated
environmental specs.
•
To avoid heat accumulation, good ventilation is required for the operating environment.
•
Keep the device away from liquids while in use.
•
While in delivery, the device shall be packed in its original packing, or packing of the same durability.
•
Regular part replacement: some equipment parts (e.g., electrolytic capacitor) shall be replaced regularly according to their average endurance time. The average time varies
because of differences between operating environments and usage history, so regular checking is recommended for all users. Contact your dealer for more details.
•
Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the
instructions provided by the battery manufacturer.
•
If the product does not work properly, contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or maintenance.)
3
L O C A L A C T I V A T I O N ( c o n t i n u e d )
T Log In (Dialog Box)
1. User Name field will be prefilled with
"admin."
2. Input Password (account locks for 30
minutes after 7 incorrect attempts).
3. Click OK.
4
I N I T I A L I Z E T H E H A R D D R I V E ( I F N E E D E D )
The system is set up to record upon power up and will beep and display "Do you want to initialize drive"
prompt if the hard drives are not initialized.
1.
Go to MENU > SYSTEM CONFIGURATION > HDD.
2.
Use the checkboxes to select the HDDs that need to be initialized.
3.
Press INIT. (Factory installed HDDs come initialized. Initializing again will erase any record video.
This does not affect settings).
. HDD LIST
3 TOTAL HDD SPACE
$ FREE SPACE
.
3
$
W H A T ' S I N T H E B O X
Make sure the following items are in your box:
NVR
Mouse
Remote
AC Cord
HDD
HDD Cables
Ear Mounts
QSG
(Installed)
(Installed)
M E N U T R E E
Use this menu tree to navigate the embedded menus.
F R O N T P A N E L
1
6
2
3
Figure 1, DS-7716NI-I4/16P Front Panel
5
S E T D A T E A N D T I M E
1.
Go to MENU > SYSTEM CONFIGURATION > GENERAL.
. DATE/TIME
Date and time settings
.
3 TIME ZONE
Time zone and daylight savings
time settings
3
$ ENABLE NTP
Network Time Protocol settings
$
6
S E T U P N E T W O R K A C C E S S
1.
A network connection is required to access the cameras remotely.
2.
Go to MENU > SYSTEM CONFIGURATION > NETWORK.
3.
Enable DHCP (check the checkbox).
4.
Press Refresh button to update the IPv4 address, subnet mask, and IPv4 default gateway.
5.
Disable DHCP (uncheck the checkbox).
6.
Change "Preferred DNS Server" value to 8.8.8.8 (leave Alternate DNS Server blank).
. GENERAL TAB
Select this tab
3 NIC TYPE
.
Set LAN type
3
$ ENABLE DHCP
$
Check box so that router will
1
assign IP address
/ REFRESH
Press to update values
1 IP V4 ADDRESS
4
Default 192.0.0.64
2
4 PREFERRED DNS SERVER
Default is 8.8.8.8
2 ALTERNATE DNS SERVER
Leave blank
/
F R O N T P A N E L ( c o n t i n u e d )
No.
Item
Description
• Power:
GREEN
when system has power and is turned on
• Ready:
GREEN
when system has booted up and is running properly
• Status:
GREEN
when DVR is controlled by IR remote,
by keyboard,
ORANGE
when IR remote and keyboard used at same time
1
Indicators
• Alarm:
RED
when a sensor alarm is detected (not motion)
• HDD:
BLINKS RED
when data is being read from or written to HDD
HDD Screws
• TX/RX:
GREEN
when connected to network,
(Installed)
network traffic
2
Navigation Pad
Moves cursor
3
Function Buttons
Calls up various functions
Jog/Shuttle
Playback: Outer ring speeds up/slows down playback, dial advances/reverses
4
Controller
playback. Menus: Outer ring/dial moves selection up/down.
5
Power Switch
Turns unit on/off
6
USB Ports
Connects USB mouse or USB flash memory devices
DVD-ROM
R E A R P A N E L
Figure 2, DS-7716NI-I4/16P Rear Panel
No.
Item
Description
1
Power Input
100 to 240 VAC
2
Audio I/O
RCA connectors
5
3
RS-232
Connects RS-232 devices
4
VGA Out
DB-15 connector for VGA output (display local video output and menu)
5
HDMI Out
HDMI video output connector
6
Power Switch
Switch for turning device on/off
7
LAN
Connector for LAN (Local Area Network)
4
8
USB
USB 3.0 port for additional devices
9
RS-485
Connector for RS-485 devices. T+ and T- pins connect to R+ and R- pins of
PTZ receiver respectively.
D+, D- pin connects to Ta, Tb pin of controller. For cascading devices, the first
DVR's D+, D- pin should be connected with the D+, D- pin of the next DVR.
10
Alarm In
Alarm input connectors
11
Alarm Out
Alarm output connectors
12
Grounding Screw
Ground
(WARNING: needs to be connected when NVR starts up)
13
Network Interfaces w/PoE
IP camera inputs and PoE outputs
14
eSATA
Connects external SATA HDD, CD/DVD-RW
7
S E T C A M E R A P O R T S
After assigning the IP information, click the More Settings tab.
The More Settings tab contains the ports that need to be forwarded for remote access.
•
SERVER PORT is responsible for the mobile app and client software log-in.
•
HTTP PORT is responsible for Web browser log-in.
•
RTSP PORT is responsible for video/audio streaming.
NOTE:
The HTTP port, server port, and RTSP can be changed to avoid conflicts
with the ISP or if multiple devices are installed at a single location.
8
S E T U P P O R T F O R W A R D I N G
Port forwarding redirects communication from one address/port number to another to make services on a
protected network available to hosts on an external network.
1.
Log into the router, and proceed with port forwarding. Port forwarding steps differ by router. For
port forwarding assistance, contact your Internet Service Provider (ISP) or router manufacturer. Also
refer to www.portforward.com for step-by-step instructions.
NOTE:
Hikvision USA is not associated with www.portforward.com and is not
responsible for any activity between the user and www.portforward.com. Please
avoid accidentally downloading any software from www.portforward.com.
2.
Proceed to the Routers section on the website for step-by-step instructions.
9
S E T U P H I K - C O N N E C T P 2 P C L O U D S E R V I C E
NOTE:
Use the Hik-Connect mobile app (from iOS App Store or Google Play) to create a
Hik-Connect P2P Cloud account to connect Hikvision devices over the Internet. See
your NVR user manual.
1.
Enable Hik-Connect P2P on the NVR.
1)
Go to Main Menu > System Configuration > Network > Platform Access.
2)
Check the Enable checkbox.
1
C O N N E C T D E V I C E S
1.
Connect AC power cord to the NVR.
2.
Connect NVR to LAN using Cat 5e cable.
RED
when controlled
3.
Connect video monitor(s) to NVR using HDMI and/or VGA cables, as appropriate.
4.
Connect mouse to USB port (wireless mouse can be used in lieu of included mouse).
5.
Connect to audio I/O using RCA connectors.
BLINKS GREEN
when there is
2
S T A R T T H E N V R
1.
Plug AC power cord into 110 to 240 VAC outlet (surge suppressor is recommended).
2.
Turn power switch on. Power indicator LED will turn
3.
After startup, power indicator LED will remain GREEN.
3
L O C A L A C T I V A T I O N
System access requires a secure, user-assigned password.
9
S E T U P H I K - C O N N E C T P 2 P C L O U D S E R V I C E ( c o n t i n u e d )
3)
Server Address must be "dev.hik-connect.com." If not, check the Custom checkbox, and type
"dev.hik-connect.com."
4)
Click the Apply button. Status will change to "Online" (if all settings are correct).
5)
Note the Serial Number and Verification Code shown here (for use when registering the NVR in
your Hik-Connect account) or use the QR code displayed.
2.
To see a device's video stream on the Hik-Connect or iVMS-4500 mobile app, add the device.
1)
Login to Hik-Connect mobile app with your user name, e-mail, or mobile number and password.
2)
On the Home screen, click the "+" button (upper right corner).
3)
Enter the device's information.
x If you have the device's QR Code: Use the QR Code Scanner to scan the device's QR Code.
x If you do not have the device's QR Code: Enter the device information manually:
a. Click the Edit (pencil) icon on top right corner.
b. Enter device serial number (device must be online), then click the OK button.
c. When the device appears on the "Results" screen, click the Add button.
d. Enter device's 6-character Verification Code (all upper case), then click the OK button.
e. Click the Finish button.
10
A D D I P C A M E R A S
1.
Right click a window in Live View mode to display the menu.
2.
Click Menu to display Menu choices.
Click Cameras Setup to display the Add Cameras window.
3.
4.
Add camera(s) as follows:
x Hikvision Camera Connected to Unit's PoE Port — Will automatically be added to an NVR
camera channel (D
x
) and will be visible on the camera list in white within two minutes.
x Hikvision Camera Connected to the Network but Not Unit's PoE Ports — Will automatically be
detected and displayed at bottom of the camera list in yellow. Must be added to an NVR camera
channel manually:
GREEN
to indicate unit is starting.
T Set Admin Password
First-time access requires user to create an
admin password.
1. Input same password in Create New
Password and Confirm New Password
text fields.
Strong Password REQUIRED
Password must contain 8 to 16 characters,
combining numbers, lower and upper case
letters, and special characters. At least two
types of the above-mentioned characters are
required. Also, reset password regularly.
2. Click OK to save password and activate
device.
T Set Unlock Pattern
Admin user will be prompted to configure an
unlock pattern for login in place of a password.
1. Hold down left mouse button and draw a
pattern by connecting at least four dots on
the screen, with each dot connected only
once). Release mouse button when done.
2. Draw the same pattern again to confirm it.
NOTE: If you forget your pattern, select
Switch User to display the normal
login dialog box.
T Log In (Unlock Pattern)
1. Draw the unlock pattern to unlock system.