Alinco DJ-191 Інструкція з експлуатації - Сторінка 12

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Трансивер Alinco DJ-191. Alinco DJ-191 18 сторінок. Cert communications team procedures
Також для Alinco DJ-191: Інструкція з експлуатації (18 сторінок), Короткий довідник (3 сторінок), Короткий довідник (4 сторінок)

Друкувати сторінку

III

8. GETTING STARTED

III

1'-/

1'-/6

1'-/6.5

1'-/6.52

@VOL

@SQL

@88

@88888

@CJ

@mmD

@ . (decimal

point)

icicicicicO

It appears while the volume level is being adjusted by either the

upward key or downward key.

It appears while the squelch level is being adjusted by pressing the

iii

key and either the upward key or downward key.

In the Memory Mode, the "M" icon appears.

In the VFO Mode, the "M" icon is not displayed.

While either the volume level or squelch level is adjusted, some

numbers will appear indicating the setting levels (min. O-max.

31).

In the Memory Mode, it indicates the selected memory channel

number (0 - 39, or "C" for call channel).

It indicates the transmit/receive frequency, offset frequency, tone

frequency, tuning step" DSQ code and AUTO DIAL code.

When the low power output is selected, the "L" icon appears.

When the "L" icon is not displayed, the high power output is

selected. (Not applicable for DJ-491C)

When the voltage of the battery is dropped and need to be

recharged, the "B" icon appears.

If it is displayed, turn off the power and recharge the battery. It will

take approximately 12 to 14 hours to be fully charged with EDC-63

or EDC-64.

The "BUSY" icon will appear when a signal is received, or

squelch is unmuted.

(During DSQ or TSQ, the audio remains muted unless the tones

match, regardless of the "BUSY" icon.)

It indicates: MHz for transmit/receive and offset frequencies.

kHz for channel step.

Hz for encoded sub-audible tone (CTCSS) tone

frequency.

In the Scan Mode, the decimal point flashes.

It indicates the received signal strength and/or the output power

level.

8-1 Receiving

1. Adjust the following and controls of the unit.

POWER SWITCH:

OFF

VOLUME CONTROL:

Set to "0" level

SQUELCH CONTROL: Set to "0" level

2. Connect a battery pack or external 4.8 - 13.8 Volt DC Regurated Power Supply to

the radio.

3. Ensure an antenna with the appropriate antenna connector is connected.

4. Turn the POWER switch on.

5. Press the upward key until a signal (or noise) is heard through the speaker.

6. The LCD display will indicate frequency.

7. Rotate the Main Tuning Dial, or enter the frequency from the DTMF keypad to select

a frequency. Press and hold the

iii

key, then press the upward key until the noise

disappears from the speaker.

KEYPAD DIRECT ENTRY

When a frequency is selected by the direct keypad entry, numbers will appear on the

LCD display as they are entered through each push of a key.

To enter a frequency directly from the keypad, perform the following.

The following example will use frequency 146.52MHz, and step of 5kHz.

1. Enter the 1OOMHz digit first. Example: 1_._

2. Enter the 10MHz digit next. Example: 14_._

3. Enter the

1MHz digit next. Example: 146._

4. Enter the 100kHz digit next. Example: 146.5_

5. Enter the 10kHz digit next. Example: 146.52_

6. Enter the

1kHz digit next. Example: 146.520

STEP KEY

The STEP function is used to select the desired incremental changes of receive/

transmit frequencies, in step of 5, 10, 12.5,15,20,25, 30kHz. Use this feature as

follows:

1. Enter the VFO MODE.

2. Press and hold the

iii

key, then press the

key.

Change the channel step by using the Main Tuning Dial.

3. Press the PTT switch to return to the operating frequency.

4. After the channel step is set, the receive/transmit frequency will increase or

decrease by the value selected when you turn the Main Tuning Dial.