Axvue KOEHOG K882 Інструкція з експлуатації

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Радіоняня Axvue KOEHOG K882. Axvue KOEHOG K882 2 сторінки. Video baby monitor with '' lcd screen & two cameras

Друкувати сторінку

INSTRUCTION MANUAL

KOEHOG K882 Video Baby Monitor

with '' LCD Screen & Two Cameras

Please read the following instructions and warnings carefully

Keep this instruction manual for the future.

For technical support see the FAQ page.

For adult use only.

FEATURES & COMPONENTS

Camera:

Monitor:

*LED

Power & Low Battery

Sound Lights

Adapter:

× 2

Revised at 4/2021

Get to know us at: www.koehog.com

Keep the distance between sensor and

0.6 in

body at least 0.6 inch for accurate

temperature result.

1. Power Indicator

2. Lens

3. Nighttime LEDs

4. Microphone

5. Temperature Sensor

6. Power On/Oﬀ Switch

7. Speaker

8. DC Jack

9. Wall Mounting Hole

1. Power/Video

2. LED

3. Left

4. Talk Back/Zoom

5. Menu/OK

6. Speaker

7. Right

8. Volume Up

9. Volume Down

10. Microphone

11. DC Jack

12. Kickstand

PLEASE INSTALL THE SUPPLIED RECHARGEABLE

BATTERY INTO THE BATTERY BOX BEFORE USING

THE BABY MONITOR FOR THE FIRST TIME.

× 3

× 1

WARNING

THIS PRODUCT CAN NOT SUBSTITUTE PARENT'S SUPERVISION

ON YOUR CHILD.

-Store this product out of the reach of babies (at least 3 feets (0.9 m)

away from the crib). A strap wound around the baby's neck may result in

asphyxiation. Use a safety clip to clamp the power cord and keep it out

Model- K882

of baby's reach. Do not use other extension cords. Only use the power

adapter provided.

-Do not touch the exposed part if the adapter is connected with power.

-Test regularly before initial use or when change the position of camera.

-Avoid placing the product in humid place or contacting with liquid. (such as bathtub, sink, etc.)

-Do not apply heat to the product. (such as stoves, radiators, etc.)

-Using the product in ventilated place. Avoid placing it on sofas, cushions, beds or other places which

may block ventilation.

-The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are

contained, please be careful when unpack and install it.

BATTERY WARNING

-Only use the recommended rechargeable battery. Please contact us if you need to change it.

For the contact list, please refer to the last page of the instruction.

-Please clean the battery compartment before using it.

-Avoid short circuits the power supply terminal.

-Remove the battery when you are not using it or when running out of power.

-Keep the battery away from children.

-Dispose of the empty battery properly.

SETUP & USE

Please charge the battery for at least 8 hours before

using the product.

Step 1: Test reception ﬁrst, put camera in a suitable place

that will provide you the best view of your baby in the crib

(Note: Do not hang up the camera ﬁrmly until initial

installation test is completed). Plug adapter into wall outlet

and turn on the camera.

Step 2: Turn on monitor by pressing and holding Power/

" button for 5 seconds until "KOEHOG" shows up,

Video

then video will show up on the screen immediately. If video

does not show up, please refer to "TO PAIR MONITOR AND

CAMERA (ADD CAMERA)" at next page. If video shows up,

the initial installation test is completed, then you can set up

the camera according to the instruction below.

Set Up Camera: Place camera on a ﬂat surface, such as

wardrobe or shelf (Figure 1). Or hang it on the wall (Figure 2).

No matter wherever to place the camera, please make sure

to keep it away from the crib for at least 3 feet and all power

cords should be placed behind the camera properly. Then

adjust the angle of camera lens until the entire crib shows up

on the display, or adjust it to the best angle that you think to

watch your baby.

TO USE PLUGGED-IN MODE

Step 1: Place the monitor display in living room, bedroom or any place you want to watch your

baby. Use adapter to connect camera with electrical outlet.

Step 2: Turn on monitor by pressing Power/Video "

or video shows up on the screen.

Step 3: Press Power/Video "

Step 4: Turn oﬀ the monitor completely by pressing and holding Power/Video "

seconds.

TO USE PORTABLE/BATTERY MODE

Please charge the battery for 6 ~ 8 hours before using the product.

Step 1: Charge the battery for at least 6 hours before using portable / battery mode.

Step 2: Make sure the adapter is plugged into camera.

Step 3: The battery life can be up to 8 hours if it is fully charged.

Battery life will be shortened if recharging it continuously. Unplug the AC adapter when you are

not using it for a long time.

TO PAIR MONITOR AND CAMERA ( ADD A CAMERA )

The monitor and the camera are paired prior to the shipment. If the monitor and

camera are found not paired for some reason, follow steps below:

Step 1: Make sure the monitor is at the same area with the camera.

Step 2: Make sure the camera AC adapters are plugged in.

Step 3: Press Power/Video "

Step 4: Press Menu/OK"

camera option"

Step 5: Using the Left "

to conﬁrm.

Step 6: Choose the identifying number to be assigned on the camera.

Step 7: Press the Menu/OK "

VOX

Step 8: Press Power/Code "

Step 9: Waiting 3 seconds, the green light stop ﬂashing once paired successfully and the video will appear.

The SCAN, SELECT, ADD, DELETE, VIEW CAMERA options are only available when

multiple cameras connected with the monitor. Order extra cameras by visiting

us at www.koehog.com or search "Axvue Baby monitor" on Amazon.

" button for 3 seconds until "KOEHOG" logo

" button to turn oﬀ the video if you only need to hear the voice.

" for 5 seconds to power on the monitor.

" shortly to enter menu, then press Right "

" function and Menu/OK"

" to conﬁrm.

" or Right "

" to highlight ADD CAM "

" button again to start pairing and the red light will ﬂash.

Red LED will ﬂash

" on the camera until the power indicator ﬂashes.

Figure 1

3 feet

Figure 2

" button for 3

" to highlight the

" and press Menu/OK"

Press