Samsung VM46R-U Посібник з швидкого налаштування
Переглянути онлайн або завантажити pdf Посібник з швидкого налаштування для Монітор Samsung VM46R-U. Samsung VM46R-U 2 сторінки.
Друкувати сторінку
Quick Setup Guide
VM46R-U
* WARNING: Please ensure this product is inspected by yourself (to identify if there are
any defects) prior to any installation. Any defect should be brought to the attention of
Samsung as soon as discovered. Please do not install the product if it appears to have
a defect. Any damage caused by carelessness in the process of installing the product
will be treated as damage caused by yourself (and not a product defect). To determine
whether or not this product has been installed Samsung will view evidence of the screw
hole label being pierced (as well as any other cosmetic evidence of an installation).
* The colour and the appearance may differ depending on the product, and the content in
the manual is subject to change without prior notice to improve the performance.
* Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
Checking the Components
Contact the vendor where you purchased the product if any
components are missing.
The pictures may look different from the actual components.
Warranty card
Quick Setup Guide
(Not available in
Power cord
some locations)
Batteries (AAA x 2)
(Not available in
Remote Control
RS232C adapter
some locations)
HDMI cable
Holder-Ring x 4
Screw (M8 x L30) x 4
-00
Troubleshooting Guide
Issues
Solutions
The screen keeps
Check that the cable between the product
switching on and off.
and the PC is connected correctly.
Check that products (including source
device) are connected correctly with a cable.
Check that the source device connected to
No Signal is
the product is powered on.
displayed on the
screen.
Depending on the type of external device,
the screen may not display properly. In this
case, connect it with the HDMI Hot Plug
function turned On.
This message is displayed when a signal
from the graphics card exceeds the product's
maximum resolution and frequency.
Not Optimum Mode
is displayed.
Refer to the Standard Signal Mode Table
and set the maximum resolution and
frequency according to the product
specifications.
The images on
the screen look
Check the cable connection to the product.
distorted.
The screen appears
Check that the resolution and frequency of
unstable and shaky.
the PC and graphics card are set within a
range compatible with the product. Then,
There are shadows or
change the screen settings if required by
ghost images left on
referring to 'Preset Timing Modes' .
the screen.
Ports
Parts
Remote sensor
1
Press a button on the remote control pointing at the sensor on the product to perform the corresponding function.
* Using other display devices in the same space as the remote control of this product can cause the other display devices to be
inadvertently controlled.
Receives the remote control signal via the external sensor board
1
and outputs the signal via LOOP OUT.
Connects to an external IR cable that receives signals from the
2
remote control.
Outputs sound to an audio device via an audio cable.
3
Connects to MDC using an RS232C adapter.
4
Connect to a USB memory device.
5
* The USB ports on the product accept a maximum constant
current of 1.0A. If the maximum value is exceeded, USB ports
may not work.
Connects to MDC using a LAN cable. (10/100 Mbps)
6
Connects to a source device using a HDMI cable or HDMI-DVI cable.
7
Connects to a source device using a HDMI cable or HDMI-DVI cable.
8
Connects to another product using a HDMI cable.
Connects to a PC using a DP cable.
9
Connects to another product using a HDMI cable.
0