ActronAir ERQ3-17AS Посібник з монтажу - Сторінка 8

Переглянути онлайн або завантажити pdf Посібник з монтажу для Аксесуари для кондиціонерів ActronAir ERQ3-17AS. ActronAir ERQ3-17AS 20 сторінок. Split ducted unit

Друкувати сторінку

INSTALLATION INSTRUCTIONS

The installation instructions provided below are intended as a guide only and does not supersede the relevant council,

state and federal codes, regulations and building code standards. Compliance and consultation with the authorities

having jurisdiction with the installation of this equipment is the responsibility of the installer. Actron Air will not be held

liable for any damages or costs as a result of the installer's failure to comply. Please refer to the matching outdoor unit

Installation and Commissioning Guide for further information and details.

LIFTING THE UNIT

Always observe WH&S regulations for safe and secure lifting

practices in order to prevent physical injury.

Suggested lifting procedures are outlined in the next page as

reference guide to safely lift and transport the unit, however,

these does not over rule the industry WH&S practices.

LOCATION

This unit is intended for indoor installation only. It is highly

recommended that this indoor unit and accessories,

particularly zone barrels, be mounted in the roof cavity.

Mount the unit in a stable and rigid support wherein the

weight is properly distributed, such as roof joist and rafters.

Take into consideration the minimum service access

clearances provided in the unit drawings.

Locate the indoor unit away from the areas where noise is

a critical factor. Use rubber mounting pad (not supplied) in

order to minimize the transfer of noise and vibration into

building structures.

A hanging bracket assembly and rubber grommet (optional

on other units) are also provided to secure the indoor unit

into the roof rafters. This installation configuration is most

suitable for installation that require the unit to be rigidly

secured up from the roof joist.

CONDENSATE and SAFETY TRAY DRAINAGE

An integrated safety drain tray is provided as a standard

inclusion to your indoor unit in order to reduce the potential of

condensate damage to the roof. Drain Kit (optional on some

units) is provided for the condensate drain to be externally

trapped from the indoor unit. Suggested condensate

and safety tray drainage instructions are provided at the

proceeding page for your reference.

SUPPLY AIR and RETURN AIR DUCT

The indoor unit is supplied with duct flange as standard in

order to facilitate the system's duct connection into the unit.

Supply and return air duct works must be adequately sized to

meet the system's air flow and static pressure requirements.

Refer to the unit drawing for supply air and return air duct

dimensions, specific to your requirement.

NOTE: Fit a flexible duct connection in between the unit

and the duct system, where noise and vibration is a critical

consideration.

RETURN AIR FILTER

Air filters must be provided in the return air side of the unit

in order to maintain the efficiency and prolong the operation

Page 8 of 20

of the unit. These are also paramount in order to satisfy

requirement for a clean and hygienic room condition. Air

filters must be placed in an easily accessible location for

service and maintenance.

NOTES:

1. Air filters are not supplied with the unit as individual air

filtration requirements are varied.

2. Ensure that filters are cleaned / replaced regularly.

SUPPLY AIR and RETURN AIR DUCT (OPTIONAL)

Supply Air plenums and Duct Plates (twin-spigot) are

available in order to facilitate your duct system connection to

the indoor unit. The supply air plenums come in 1-way, 2-way

and 3-way options, which offer a wider solutions to your

different air distribution requirements.

SPLIT FAN COIL SYSTEM (OPTIONAL ERQ4-19AS)

The Actron Air innovative 2-piece fan coil system provides

a solution to your difficult and tight roof space installation

requirement. This versatile system has a separate fan and

coil sections. Each of the compact and lightweight section

is simply installed in two separate locations and joined by

flexible duct system. Air ducts are attached to each section

of the split fan coil by both of the supply air plenum and the

twin spigot duct plate.

FAN COIL w/ VERTICAL DISCHARGE (OPTIONAL)

An upright Fan Coil with vertical supply air discharge is

also available wherein installation applications require the

placement of the unit down in a closet, basement or garage.

Please refer to the Technical Catalogue of your indoor unit

for dimensions, installation details and specifications.

FIELD PIPE CONNECTIONS

Specifications and installation requirements for field

pipe connections are contained in the Installation and

Commissioning Guide of the outdoor unit that matches

your indoor unit. Please refer to this guide and thoroughly

understand the procedures for safe and correct indoor and

outdoor connection.

ELECTRICAL FIELD CONNECTION

The power supply and control communication data to the

indoor unit are supplied via the outdoor unit. Please refer

to the wiring diagram supplied with the outdoor unit for

specifications.

All electrical work must be performed by a licensed

electrician and must conform with the wiring diagram and all

relevant electrical authorities.

Installation & Commissioning Guide - ESP Platinum ID Split Ducted Units

Doc. Part No. 0525-052 Rev. 5 200928