Yamaha Clavinova CLP-110 (Німецька) Інструкція з експлуатації - Сторінка 35
Переглянути онлайн або завантажити pdf (Німецька) Інструкція з експлуатації для Електронна клавіатура Yamaha Clavinova CLP-110. Yamaha Clavinova CLP-110 46 сторінок. Yamaha digital piano owner's manual
Також для Yamaha Clavinova CLP-110: Короткий посібник з експлуатації (2 сторінок), Посібник користувача (46 сторінок), (Французька) Mode D'emploi (46 сторінок)
4. PROGRAM CHANGE
Data format: [CnH] -> [ppH]
CnH = Program event (n = channel number)
ppH = Program change number
CLP-110
MSB
LSB
Grand Piano 1
0
122
Grand Piano 2
0
112
E.Piano 1
0
122
E.Piano 2
0
122
Harpsichord 1
0
122
Harpsichord 2
0
123
Vibraphone
0
122
Church Organ 1
0
123
Church Organ 2
0
122
Strings
0
122
• When program change reception is turned OFF, no program
change data is transmitted or received. Also, Bank MSB/LSB
is not transmitted or received.
5. SYSTEM REALTIME MESSAGES
[rrH]
FEH: Active sensing
Data
Transmission
If a signal is not received via MIDI for
more than 400 milliseconds, the
Transmitted every
same processing will take place for
FEH
200 milliseconds
All Sound Off, All Notes Off and Reset
All Controllers as when those signals
are received.
• Caution: If an error occurs during MIDI reception, the Damper,
Sostenuto, and Soft effects for all channels are turned off and
an All Note Off occurs.
P.C.#=Program Change number
P.C.#
0
0
5
4
6
6
11
19
19
48
Reception
6. SYSTEM EXCLUSIVE MESSAGES
(Universal System Exclusive)
(1) Universal Realtime Message
Data format: [F0H] -> [7FH] -> [XnH] -> [04H] -> [01H] ->
[llH] -> [mmH] -> [F7H]
MIDI Master Volume
• Simultaneously changes the volume of all channels.
• When a MIDI master volume message is received, the volume
only has affect on the MIDI receive channel, not the panel
master volume.
F0H = Exclusive status
7FH = Universal Realtime
7FH = ID of target device
04H = Sub-ID #1=Device Control Message
01H = Sub-ID #2=Master Volume
llH =
Volume LSB
mmH = Volume MSB
F7H = End of Exclusive
or
F0H = Exclusive status
7FH = Universal Realtime
XnH = When n is received n=0~F, whichever is received.
X = don't care
04H = Sub-ID #1=Device Control Message
01H = Sub-ID #2=Master Volume
llH =
Volume LSB
mmH = Volume MSB
F7H = End of Exclusive
(2) Universal Non-Realtime Message (GM On)
General MIDI Mode On
Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] ->
[F7H]
F0H = Exclusive status
7EH = Universal Non-Realtime
7FH = ID of target device
09H = Sub-ID #1=General MIDI Message
01H = Sub-ID #2=General MIDI On
F7H = End of Exclusive
or
F0H = Exclusive status
7EH = Universal Non-Realtime
XnH = When received, n=0~F.
X = don't care
09H = Sub-ID #1=General MIDI Message
01H = Sub-ID #2=General MIDI On
F7H = End of Exclusive
When the General MIDI mode ON message is received, the
MIDI system will be reset to its default settings.
This message requires approximately 50ms to execute, so
sufficient time should be allowed before the next message is
sent.
Appendix
35
CLP-110