ARO 8212-1B series Посібник оператора - Сторінка 6

Переглянути онлайн або завантажити pdf Посібник оператора для М'ясорубка ARO 8212-1B series. ARO 8212-1B series 7 сторінок. 0 series

MODEL IDENTIFICATION
MODEL
NUMBER
7015-11
RPM
LEVER
END
CYLINDER
MOTOR
COLLET
COLLET
COLLET
THROTTLE
THROTTLE
HOUSING
ASSEMBLY
(ITEM 9)
(ITEM 12)
PLATE
ASS'Y
ASS'Y
(ITEM 31
CAPACITY
(ITEM 17)
(ITEM 21)
or 35
18,000
LEVER
43582
43583
31023
30750
30612
33804
39954-3
37431-3
3/16" - 1/4"
7015-11-EU
18,000
LEVER
49940
46941
47052
30750
30912
33804
39959-3
37431-3
5-6mm
8212-1B
21,000
LEVER
43602
43583
31023
37968
30612-1
43581
41753-3
41750-3
1/4"
8212-1B-EU
21,000
LEVER
49640
49641
47052
37956
30612-1
43581
41753-12
41750-12
6mm
8213-1B
21,000
BUTTON
43685
43584
37956
30912-1
43581
41753-3
41750-3
1/4"
CANCELLED MODELS
MODELS WITH -EU SUFFIX ARE "EC" COMPLIANT MODELS.
DISASSEMBLY/ASSEMBLY
INSTRUCTIONS
l
l
0
l
l
0
-
-
-
-
Never apply excessive
pressure by a holding device which
may cause distortion of a part.
Apply pressure evenly to parts which have a press fit.
Apply even pressure to the bearing race that will be press
fitted to the mating part.
Use correct tools and fixtures when servicing this tool.
Don't damage "0" rings when servicing tool.
Use only genuine ARO replacement
parts for this tool. When
ordering, specify part number, description, tool model number
and serial number.
THROTTLE
DlSASSEMBLY
Secure tool in a suitable holding device, locating on flats of
valve housing.
Unthread and remove valve plug (1) and "0" ring (2).
Regulator (4), "0" ring (3), spring (5) and valve stem (7 or 8),
with "0" ring (6), can now be removed from housing.
THROTTLE
ASSEMBLY
Lubricate and assemble "0" ring (6) to valve stem.
Assemble valve stem, spring (5) regulator (4) and "0" ring (3)
to housing and secure with "0" ring (2) and valve plug (1).
NOTE: When assembling
regulator (4) to housing, align hole
in regulator with air inlet of housing.
MOTOR DISASSEMBLY
Remove collet nut and Collet.
Insert a 5/32" hex wrench thru collet body (30 or 34) and en-
gage hex in end of rotor shaft.
Hold rotor shaft secure with hex wrench and remove collet
body using wrench (30131) on flats of collet body.
Secure housing and remove lock nut (29 or 33).
Remove muffler strip (27) and exhaust spacer (26).
Remove motor assembly from housing.
Tap threaded end of rotor (18) with a soft face hammer; motor
will come apart. NOTE: Bearings
are light press fit in end
plates and press fit on rotor.
MOTOR ASSEMBLY
Assemble
bearing (16) to end plate (17) pressing on outer
race of bearing.
Assemble end plate (17) to rotor (18) pressing on inner race
of bearing.
Coat rotor blades (19) with ARO 29665 spindle oil and as-
semble to rotor slots - straight side out.
Coat i.d. of cylinder (21) with ARO 29665 spindle oil and as-
semble over rotor. NOTE: Roll pin (20) must be aligned with
.116" diameter hole in end plate (17).
Assemble
spacer (23) and bearing
(24) to end plate (22).
pressing on outer race of bearing.
Assemble
end plate (22) to rotor, pressing on inner race of
bearing. Be sure rotor turns without binding. If rotor binds, tap
threaded end lightly with a soft face hammer to loosen.
Assemble
shield (15) and cap (14) to end plate (17).
Assemble
spacer (25) - models 7015-11-(
) only - to rotor
shaft.
Assemble collet body to rotor shaft and tighten securely.
Assemble
motor to housing.
Assemble "0" ring (28) muffler strip (27) and exhaust spacer
(26) to lock nut (29 or 33) and assemble lock nut to housing,
securing motor.
Assemble collet and collet nut to collet body.
47052 LOCK-OFF
LEVER ASSEMBLY
Y178-6 ROLL PIN
45778 SPRING
47204 LEVER
NOT SHOWN
ROLL PIN 48548