AMD DIrect SSRFR-24DK1 Benutzerhandbuch - Seite 5

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Kegerators AMD DIrect SSRFR-24DK1 herunter. AMD DIrect SSRFR-24DK1 9 Seiten.

Seite drucken

BEFORE OPERATING

Important

BEFORE USING YOUR APPLIANCE

Remove the exterior and interior packing. Before

connecting the appliance to the power source, let it

stand upright for approximately 24 hours. This will

reduce the possibility of a malfunction in the cooling

system from handling during transportation. Clean

the interior surface with lukewarm water using a soft

cloth.

Shipment Arriving Damaged:

VISIBLE DAMAGE

If your shipment arrives with visible damage to the

box/carton, be sure the damage is noted on the

bill of freight or express receipt and signed by the

person making the delivery. File a claim for damages

immediately, regardless of the extent of damage.

CONCEALED DAMAGE

If damages are unnoticed until the kegerator is

unpacked, notify the transportation company or

carrier immediately and file a concealed damage

claim with them. This should be done within (5)

days of the delivery date. Be sure to hold on to

the box/carton for inspection. We cannot assume

responsibility for damage or loss incurred in transit.

Important Notes:

CONSTRUCTION ZONES

Keep all stainless steel products away from

construction zones. Construction debris such as

(but not limited to) stone dust, stucco, and lime dust

could damage or permanently discolor stainless

steel products. Keep all caustic chemicals including

chlorine and pool cleaning products away from

stainless steel at all times.

WARNING

ELECTRICAL PARTS & COMPONENTS

Disconnect all power supplies and batteries

before servicing.

INTERIOR LIGHT

This unit is equipped with an interior LED light which

will be turned ON when the door is open and the

interior fan is stopped at the same time. You can

press

to manually turn on or turn off the light.

KEGERATOR USER MANUAL

DEFROSTING

The unit defrosts automatically in normal operating

conditions. The evaporator behind the rear wall of

the unit defrosts automatically. The condensation

collects in the drainage channel behind the rear wall

of the unit and flows through the drainage hole into

the drop tray by the compressor where it evaporates.

However, frost may accumulate on the evaporator

if the unit is repeatedly opened in a high heat or

high humidity location. If this frost pattern does not

clear within 24 hours, your unit will require manual

defrosting.

Press

and hold for 6 seconds to defrost the unit.

To stop defrosting, repeat the same interaction.

TEMPERATURE ALARM

An audible alarm sounds if the storage temperature is

not cold enough. The temperature display flashes at

the same time.

The cause of the temperature being too high may be:

• Too much warm ambient air flow when rearranging

and removing stored items.

• Prolonged power failure.

• The appliance is faulty.

The audible alarm is automatically silenced and

the temperature display stops flashing when the

temperature is sufficiently cold again.

CLEANING AND MAINTENANCE

Periodic cleaning and proper maintenance will ensure

efficiency, top performance and long life.

The maintenance intervals listed are based on normal

conditions. You may want to shorten the intervals if

you have pets or other special considerations.

Exterior cleaning for your stainless steel model:

• Turn off the power, unplug the appliance, and

remove all items – including the dispense kit.

• Wash the inside surfaces with warm water and

baking soda solution. The solution should be

appoximately 2 tablespoons baking soda by 1 quart

water.

• Wring excess water out of sponges or cloths when

cleaning controls or electrical parts.

• Wash the outside cabinet with warm water and mild

liquid detergent. Rinse and wipe dry with a clean

soft cloth.

• Do not use steel wool or a steel brush on the

stainless steel. These will contaminate the stainless

steel with steel particles and rusting may occur.

• Dust the front grill and back of the unit twice yearly,

making sure the power is off before cleaning.

• It is recommended to clean the unit yearly, inside

and out, to maximize the longevity of the product.

TROUBLESHOOTING

You can solve many common problems easily, saving

you the cost of a possible service call.

Reference the troubleshooting table below before

calling the servicer.

PROBLEM

SOLUTION

Kegerator does not operate

Not plugged in or the appliance is turned off.

The circuit breaker tripped or a fuse has blown out.

Kegerator is not cold

Check the temperature control setting.

enough

External environment may require a higher setting.

The door is opened too often.

The door is not closed completely.

The door gasket is not sealing properly.

Kegerator is turning on and

The room temperature is hotter than normal.

off frequently

The door is opened too often.

The door is not closed completely.

The temperature control is not set correctly.

The door gasket does not seal properly.

The light does not work

Not plugged in.

The circuit breaker tripped or a fuse that the kegerator

is plugged into has blown.

The light bulb has burned out.

The light button is "OFF"

PROBLEM

SOLUTION

Vibrations

Check to assure that the kegerator is on a level

surface.

The kegerator seems to

A faint humming noise may come from the flow of the

make too much noise

refrigerant, which is normal.

As each cycle ends, you may hear gurgling sounds

caused by the flow of the refrigerant in your kegerator.

Contraction and expansion of the inside walls may

cause popping and crackling noises.

During the defrosting process you may hear a water

flowing sound caused by water flowing through the

drain trough.

The kegerator is not on a level surface.

The door will not close

The kegerator is not on a level surface.

properly

The gasket is dirty.

The shelves are out of position.

Smell/Odor

Check for leaks on inside surface or around the

keg coupler.

Outer surface of appliance

Condensation has formed and can be wiped dry.

is wet

External surface is warm

Compressor is working to transfer heat from inside

the cabinet.

Before Use:

Before connecting the unit to the power source, let it

stand for approximately 24 hours. This will reduce the

possibility of malfunction in the cooling system from

handling during transportation.

1. Position the unit on a flat, level surface capable of

supporting the entire weight of the unit. Remember

the unit will be significantly heavier once it is fully

loaded.

2. Connect the unit to a Ground Fault Interrupter (GFI).

3. The unit must be installed according to your local

codes and ordinances.

4. ELECTROCUTION HAZARD!

• Electrical Grounding Required - This appliance is

equipped with a three prong (grounding) polarized

plug for your protection against possible shock

hazards.

• NEVER remove the round grounding prong from

the plug.

• NEVER use a two prong grounding adapter.

5. Remove the exterior and interior packaging, but do

not remove any foam insulation surrounding the

pipes at the back.

6. Clean the interior surface with lukewarm water

using a soft cloth.

7. Place the unit on a flat, solid floor that is strong

enough to support it when it is fully loaded. To

level the appliance, adjust the rolling casters at the

bottom of the unit.

8. When moving your kegerator, please do not incline

it more than 45 degrees.

9. Locate the appliance away from direct sunlight

and sources of heat (stove, heater, radiator, etc.).

Direct sunlight may affect the acrylic coating and

heat sources may increase electrical consumption.

Extreme cold ambient temperatures may also

cause the unit to perform improperly. The optimal

ambient temperature range is 50°F - 109.4°F. Do

not mount the draft tower remotely, as the exposed

beer line will not be refrigerated, causing foam.

10. Avoid locating the unit in damp areas.

11. Unwind the power cord to its full length and

inspect for damage before plugging into the outlet.

12. Plug the kegerator into an exclusive, properly

installed and grounded wall outlet.

13. Do not under any circumstances cut or remove

the third (ground) prong from the power cord.

Any questions concerning power and/or electrical

grounding should be directed to a certified

electrician or authorized products service center.

14. After plugging the appliance into a wall outlet,

allow the unit to cool down for 3 to 4 hours before

installing a keg in the appliance.

It is recommended that you install the appliance

in a place where the ambient temperature is

between 50°F and 109.4°F (10°C-43°C). If the ambient

temperature is above or below recommended

temperatures, the performance of the unit may

be affected. For example, placing your unit in

extremely cold or hot conditions may cause interior

temperatures to fluctuate. The operating temperature

range may not be reached.