American Standard 9445.124.339 - 9445.124.339 Cardiff Vessel Stand Contemporary Style Vanity Montage- und Installationsanleitung Handbuch - Seite 4
Blättern Sie online oder laden Sie pdf Montage- und Installationsanleitung Handbuch für Inneneinrichtung American Standard 9445.124.339 - 9445.124.339 Cardiff Vessel Stand Contemporary Style Vanity herunter. American Standard 9445.124.339 - 9445.124.339 Cardiff Vessel Stand Contemporary Style Vanity 6 Seiten. Assembly instructions
Seite drucken
Optional Laminate Marble Top Installation
NOTE: Tops are precut to accommodate recommended sinks and faucet.
OPTION 1: Glass Vessel
Spread a thin coat of sealant over the top beveled surface of the riser.
1
Place the cup-like rubber washer tapered side up in the recess provided
in the riser. Place the sink over the riser.
The sink is mounted and secured on the countertop by the grid drain
2
assembly, which is installed as follows:
1. Place a bead of Plumbers' putty with the second rubber washer
beneath the rim of the grid drain body.Insert the drain through the sink.
2. Install the lock-nut from beneath the counter surface. Hand tighten.
3. Level sink front-to-back and side-to-side.
4. Install tail piece, clean sealant residue from grid drain rim and spacer.
Apply a bead of silicon adhesive to the rim of the vanity. Place the marble
3
top centered left to right on the vanity and with the back edge of the top
even with the rear of the vanity. Clean up any excess silicon.
Connect the trap to the drain assembly and hand tighten to check
4
alignment. It may be necessary to cut off part of the tail piece (area "B")
or part of the horizontal leg of the trap (area "C").
Install faucet and connect to supply in accordance with the
5
manufacturer's instructions.
Water test unit, check for leakage and correct as needed.
6
OPTION 2: China Vessel
Mount the drain assembly onto the sink. Apply a bead of Plumbers' putty
1
on the underside of the drain to ensure a watertight seal between the sink
and the drain. Remove excess putty.
Install the sink onto the laminate marble top using sealant. Remove excess
2
compound around the base of the sink. Form a fillet of sealant with a wet
finger or sponge.
Repeat Steps 3-6 listed above to complete installation..
3
Care and Cleaning of Vanity
Clean the product by using soft, slightly damp cloth. Buff the product by using a soft dry cloth. Avoid using silicone cleaners
and waxes.
Clean up excess water and spills immediately. Use a blotting rather than a wiping action. Water left over a long period of time
will cause white spots in the finish.
NOTE: Please note that some chemicals may damage the finish. Take care to avoid the following: iodine, hair dye, after shave
lotion, shaving cream, alcohol, perfume, Lestoil®, Lysol Tub and Tile Cleaner®, Lysol Spray Disinfectant®, Dow Disinfectant®,
acetone, paint remover, Formula 409®, Tile-X®, and Nair®.
Care and Cleaning of Vanity Top
When cleaning your vanity top, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid
detergents, disinfectants, or cleaning products in aerosol cans.
2
BASIN
- 4 -
GRID
DRAIN
BODY
RUBBER
WASHER
LOCKNUT
SEALANT
SPACER
SEALANT
CUTOUT
METAL
WASHER
LOCKNUT
TAILPIECE
4
C
B
7 3 0 1 0 0 3 - 1 0 0 Re v. A
COUNTER
SURFACE
(TYPICAL)