American Standard Scala Corner Whirlpool and Bathing Pool 2664.102 Spezifikationsblatt - Seite 2

Blättern Sie online oder laden Sie pdf Spezifikationsblatt für Badewannen American Standard Scala Corner Whirlpool and Bathing Pool 2664.102 herunter. American Standard Scala Corner Whirlpool and Bathing Pool 2664.102 2 Seiten. Whirlpool & bathing pool high gloss acrylic

American Standard Scala Corner Whirlpool and Bathing Pool 2664.102 Spezifikationsblatt
552mm
(21-3/4)
216mm
(8-1/2)
19mm(3/4)
CUTOUT DIMENSION
C L
OF DRAIN OUTLET
38mm
13mm (1/2) INTEGRAL
(1-1/2)
TILE FLANGE
LEVELING
STRINGER
(NOT FOR
SUPPORT)
60mm
(2-3/8)
124mm
4-7/8
GENERAL SPECIFICATIONS FOR 2664 WHIRLPOOL
60 x 60 x 19-3/4 In. (1524 x 1524 x 502mm)
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
3
CUBE (FT
)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM I PUMP
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE
INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED.
ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
CONCEALED PIPING NOT INCLUDED.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE
WITH CIRCULATING SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES
DRILLED BY INSTALLER.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI
Standard Z124.1. These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided pages.
25mm (1)
INTEGRAL TILE
FLANGE (2) SIDES
254mm X 254mm
(10 X 10) DRAIN
OUTLET CUTOUT
ON/OFF
406mm
SWITCH
(16)
PROVIDE ACCESS
1041mm
FOR SERVICING
(41)
PUMP & CONTROLS
95mm
464mm
(3-3/4)
18-1/4
ROUGH
FLOOR
INTEGRAL
1-1/2" N.P.T.M. THREADS
FEET
1-1/2" O.D. TAILPIECE
SUPPORT
114 Lbs. ( 51 Kg.)
781 Lbs. (351 Kg.)
80 Gal. (303 L)
58 Gal. (220 L)
42 x 28 In. (1067 x 711mm)
60 x 40 In. (1524 x 1016mm)
14 In. (356mm)
37 Lbs./Sq.Ft. (182 Kgs./Sq.m)
41.7
68.4
1.0 HP, 9.9 AMPS,120V.
© 2002 American Standard Inc.
WHIRLPOOL & BATHING POOL
552mm
(21-3/4)
216mm
(8-1/2)
19mm(3/4)
CUTOUT DIMENSION
C L
OF DRAIN OUTLET
38mm
13mm (1/2) INTEGRAL
(1-1/2)
TILE FLANGE
502mm
LEVELING
(19-3/4)
STRINGER
(NOT FOR
SUPPORT)
124mm
4-7/8
GENERAL SPECIFICATIONS FOR 2664 BATHING POOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
SCALA CORNER™
HIGH GLOSS ACRYLIC
254mm X 254mm
(10 X 10) DRAIN
OUTLET CUTOUT
406mm
(16)
1041mm
(41)
95mm
(3-3/4)
INTEGRAL
1-1/2" N.P.T.M. THREADS
60mm
FEET
(2-3/8)
1-1/2" O.D. TAILPIECE
SUPPORT
60 x 60 x 19-3/4 In. (1524 x 1524 x 502mm)
94 Lbs. (42 Kg.)
761 Lbs. (342 Kg.)
80 Gal. (303 L)
42 x 28 In. (1067 x 711mm)
60 x 40 In. (1524 x 1016mm)
14 In. (356mm)
36 Lbs./Sq.Ft. (177 Kgs./Sq.m)
25mm (1)
INTEGRAL TILE
FLANGE (2) SIDES
464mm
18-1/4
502mm
ROUGH
(19-3/4)
FLOOR
41.7
68.4