Astivita WMTL7KGWH Benutzerhandbuch - Seite 10

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Waschmaschine Astivita WMTL7KGWH herunter. Astivita WMTL7KGWH 11 Seiten. Full automatic electric washing machine

Seite drucken

Cleaning and Maintenance of the washing machine

End of program

The washing machine will send off the

sound of "dou-dou" at the end of any

program operation to remind you to take

out the laundry or operate it again.

After the sound, the washing machine

returns to its power-off state with no

display and all lights off.

Please shut off the tap, pull out the plug

when not in use to avoid water leakage or

the fire accidents.

Clean the water inlet

After long time use, the water inlet mesh

bag may be blocked with smudginess, and

should be cleaned according to the

following steps:

1.Switch on the power, followed by shutting

off the tap.

2.Let the washer works for 5 seconds so

that water flows into the tub through the

water inlet hose. then turn off the power.

3.Unload the water inlet hose and clean

the mesh bag, then restore the water inlet

assembly.

Clean the lint filter in the drain pump (only for having drain filter)

1. Drain the water out of the

2. Loosen the pump

pump, under which use a

cover anticlockwise.

container to collect.

4. Clean the filter.

5. Restore it and adjust

the convex place to align

at the pump hole.

Note:If the drain filter is not cleaned at proper time (every 10 times of use), Drain problem could

be caused.

Maintenance

Use gentle clothing to wipe off the water and

dirt on the surface each time after using the

washing machine. Detergent, propellant and

other chemicals are not allowed

to use so as to avoid any

damage to the plastic

accessories.

Clean Of the filter

After using the washing machine for a period

please clean it according to the following steps

1 Take out the lint filter

2 Open the filter and wash it clean in the water

3 Restore it and fix it

(only for magic filter)

After using the washing machine for a

period, please clean it according to the

following steps:

1.Take off the lint filter.

2.Turn over the mesh bag and wash it

clean in the water.

3.Restore it and fix it.

(only for normal filter)

3. Take out the lint filter.

6. Tighten the pump cover

clockwise.

Identify usual trouble of washer

When the washer is in trouble, please contact local service office or the sales service

department of our company and the customer should not dismantle the machine without

permission.

If the washer can not work normally, or appear abnormity or alarms, please check and

correct as follows.

List of faults and inspection

Faults

If the power is off or the fuse is burned out.

If the water supply is cut off or the water pressure is too low.

If the inlet hose is properly connected and the water tap is opened.

If the filtering screen of inlet valve is blocked by dirt.

No water

If the coil of inlet valve is damaged. (The slight electromagnetic

flows in

sound is normal phenomenon when the inlet valve is switched on)

If the "Start / Pause" button is pressed after the power

switch is pressed.

If the power is off or the fuse is burned out.

If the power supply voltage is too low.

If the water amount reaches to the required water level.

(The washer will not work if the water amount does not reach the

washing

required water level)

If it is set to "Delay" washing mode. (It will only start to work

until the reservation time reached)

If the water drain hose is placed very high.

Abnormal

If the end of water drain hose is sealed in pond.

draining

If the internal rubber ring of drain valve is blocked by dirt.

If the door lid is closed.

If all clothing piled largely at one side of barrel or the clothing

Abnormal

is excessively placed.

If the washer is not placed in stable condition or it is placed in

spin

inclination state. (The ground is not flat).

If the motor belt is loosened.

Note: During the de spin process, if washing are piled at one side of the spin barrel,

it will cause unbalance of spin barrel resulting in striking. At this moment, the

computer inside the washer will feel this unbalance phenomenon and will automatically

correct it ( fill in water Washing ). However, if unbalance situation is not removed after

continuous three corrections, which means the computer auto-correction can not

resolve the problem. Then the user has to manually and evenly place the clothing

inside the barrel to solve the problem.

Inspection Items