Aston Global EMERALD EM2000 Benutzerhandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für UPS Aston Global EMERALD EM2000 herunter. Aston Global EMERALD EM2000 4 Seiten.

Seite drucken

SAVE THESE INSTRUCTIONS

This manual contains important safety instructions. Please follow all instructions carefully during

installation. Read this manual thoroughly before attempting to unpack, install or operate.

CAUTION-

To prevent the risk of fire or electric shock, install in a temperature and humidity

controlled indoor area, free of conductive contaminants.

CAUTION-

Risk of electric shock, do not remove the cover. No user serviceable parts. Refer

servicing to qualified service personnel.

CAUTION-

Risk of electric shock, hazardous live parts inside this UPS can be energized from the

battery supply even when the input AC power is disconnected.

CAUTION-

Risk of electric shock, Battery Circuit is not isolated from AC input, hazardous voltage

may exist between battery terminals and ground. Test before touching.

NOTICE-

The UPS is designed to be for use with computer loads only.

Inspection

Inspect the UPS upon

receipt. Notify the carrier

and dealer if there is

damage. The package is

recyclable; save it for reuse

or dispose of it properly.

Inspect accessories:

①

Power cable 1PCS

②

USER MANUAL

1PCS

Connect Modem/ Phone / Network for Surge Protection(only for

the mode with RJ-45)

Connect a single modem/phone line

into surge-protected "IN" outlet on the

back

panel of the UPS unit. Connect from

"OUT" outlet to the computer with another phone

line cable.

Cold Start Function

When the UPS is off and there is no

power utility, it's still possible to cold

start the UPS unit to power the loads.

GRs - 1000 / 1500 / 2000 - LED

FRONT PANEL(STANDARD)

1. AC input outlet

2. Fuse

3. Output receptacles

USER'S MANUAL

1000VA/1500VA/2000VA

IMPORTANT SAFETY INSTRUCTIONS

Choose an installation location

Software Download and Installation

Please follow steps below to download and install monitoring software:

1. Go to the website http://www.Ablerex.com

2. Click Emily II software icon and then choose your required OS to down load the software.

3. Follow the on-screen instructions to install the software.

4. When your computer restarts, the monitoring software ※Software only for the model with communication port.

FRONT PANEL EXPLANATIONS

Symbol

LED

Description/function

Color

Tack switch for

N/A

Turn-on/Turn-off

Lit: Line mode

Dim: Abnormal input voltage

Green

and frequency in standby

mode

Flashing: Standby mode

Lit: Battery mode

Yellow

Flashing: Battery Low

Lit: System malfunction or

Red

abnormal

REAR PANEL EXPLANATIONS

SETUP

Connect the loads

Plug in the AC input cord to the Utility(Make sure the

voltage of Utility matches with the input

voltage window of the UPS)

※Plug the UPS into the wall outlet to charge the UPS for

over 8 hours before using the UPS.

Plug in the loads to output receptacles on the rear panel

of the UPS.

Caution：Do not connect a laser printer to the outlets.

These UPS outlets provide battery power to the

equipment when utility voltage is outside acceptable limits.

Connect

Computer

Interface Port

(Optional)

Connect the optional interface

cable to the USB interface

port on the back of the UPS.

Connect to the computer. See

software document for installation instruction.

GRs - 1000/1500/2000 - LCD

FRONT PANEL(OPTION))

4. RS-232 or USB port (option)

5. Modem/LAN Internet Protection (option)

6. Fan (only for GRs 1500/2000)

Turn ON/OFF the UPS

Turn on the UPS: Press the UPS

On/OFF Switch for approx. 3 seconds,

then the Buzzer sounds twice, the UPS

will be start-up.

Turn off the UPS: Press the UPS

On/OFF Switch for approx. 3 seconds,

then the Buzzer sounds twice, the UPS

will be shutdown.

1.Line mode

4. Battery capacity

2.Battery mode

5. Load level

3.AVR mode

6.Measurement

Target & Value

192321982025002

7.Fault

8.Tack switch for

Turn-on/Turn-off