Donovan Hammer II Benutzerhandbuch - Seite 3

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Industrielle Ausrüstung Donovan Hammer II herunter. Donovan Hammer II 20 Seiten. Arm system for belly dumps, end dumps, dump bodies & pups

Seite drucken

P/N 1809533 Rev. B

MESSAGE TO OWNERS

Thank you for buying this tarping system from Shur-Co

ate your confidence in our products. Please read and thoroughly un-

derstand this manual before installing and/or operating this system.

Pay particular attention to important safety and operating instructions,

as well as warnings and cautions. The hazard symbol

alert users to potentially hazardous conditions and is followed by cau-

tion, warning or danger messages.

Failure to READ AND FOLLOW INSTRUCTIONS could result in fail-

ure of your tarping system and/or personal injury. Your trailer require-

ments may, however, call for minor variations to these instructions.

Please inspect your tarping system periodically. Repair or replace

worn or damaged parts to your system.

QUESTIONS? CALL OUR HELP LINE:

1-800-327-8287

MON-FRI 8 AM-5 PM EASTERN TIME

We at Shur-Co

are concerned with your safety and the safety of all

those operating this system. Therefore, we have provided safety de-

cals at various locations on your tarping system. Keep decals as clean

as possible at all times. Replace any decal that has become worn

or damaged, painted over or otherwise difficult to read. Replacement

decals are available through Shur-Co

SAFETY INSTRUCTIONS

1. Always wear safety glasses during installa-

tion and operation.

2. Stay clear of moving parts.

3. Do not operate under low-hung power lines.

Always check for overhead obstructions be-

fore opening or closing.

4. Open and close tarp only at the job site.

5. Face vehicle into wind when opening and

closing tarp.

6. Install tarp on axle to roll off the top and to-

ward the rear of the box.

7. No other use of this system is authorized,

except as designed.

RUST PREVENTION

To prevent rust, paint all exposed metal, such as weld seams and/or

metal exposed by grinding or cutting, with corrosion-resistant paint.

. We appreci-

SAFETY

dealers.

Hardware Identification ....................................................................... 1

Front Drive Installation .....................................................................2-5

Pivot Point Location ............................................................................ 6

External Pivot Mount Installation ........................................................ 7

Arm Installation ................................................................................... 8

is used to

Tarp Tube Assembly & Tarp Installation ..........................................9-10

Rotary Switch Kit Wiring ................................................................... 11

Manual Crank Installation ............................................................12-13

Replacement Parts ......................................................................14-15

Wrenches - 1/2", 9/16", 3/4"

Ratcheting Socket Wrench

Sockets - 1/2", 9/16", 3/4"

Allen Wrenches - 1/8", 5/32", 3/16"

Drill Bits (metal cutting) - 5/16", 3/8", 1/2"

Center Punch

Hammer

Tape Measure (2)

Flat Head or Phillips Screwdriver

10. Grinder or File

11. Air or Electric Impact Wrench w/9/16" Socket

12. Metal Saw

Additional tools needed, depending on kit configuration:

Retaining Ring Pliers

Wrench or Nut Driver - 10mm

Large Pipe Wrench

Steel Welder

Aluminum Welder

• Spray all bearings with penetrating oil as needed.

• Grease spring bearings as needed.

• Brush springs with steel brush weekly to remove dirt and spray with

penetrating oil.

• Tighten any loose bolts.

• Make sure arms are not hitting sides of box. Replace damaged/

bent arms.

• Replace worn or broken springs.

• Replace/repair worn or damaged tarps.

Hammer™ II

TOOLS REQUIRED

MAINTENANCE

Donovan Hammer II Benutzerhandbuch - Seite 3

TABLE OF CONTENTS