DoorKing 8054 MicroPlus Installations- und Programmieranleitung - Seite 2
Blättern Sie online oder laden Sie pdf Installations- und Programmieranleitung für Empfänger DoorKing 8054 MicroPlus herunter. DoorKing 8054 MicroPlus 2 Seiten. Rf
Seite drucken4.1 MASTER CODE
1.
Press and release the MASTER CODE button on the side of
the receiver case.
2.
Enter a four digit code
g-I LI
and then press
EI
(beep).
4.2 ADD A TRANSMITTER(S)
1.
Press r.:::Jl:!JL[I and the four digit master code
GlG1G1GJ
(beep).
2.
Enter the two digit button number
QQ
that the recaiver is to
respond to, then press
EI
(beep).
Button 1 enter
rDIIJ
Button 2 enter
I]E]
Button 3 enter
tE:E
Buttons
1&2
together enterGlD
Buttons 2&3 together enter
l!ll!I
Buttons 1 &3 together enter
IClEJ
3.
Enter the four digit facility code (J"' - -::;;:""' I I-""' I J""-I. then press
EI
(beep).
Valid facility code numbers are: 0000 - 4095
4.
Enter the five digit beginning transmitter number
I-I:!-I:II
I-I
then press
EI
(beep).
5.
Enter the five digit ending transmitter number
QGl-lt-IQ
then
press
EI
(beep).
Valid transmitter numbers are: 00000 - 65407
If programming a single transmitter, the beginning and ending
transmitter number will be the same.
6.
Enter the time zone number
g
then press
EI
(beep).
Valid time zone numbers are: 0 - 9
There are 10 available time zones, however only time zones
2 - 9 are programmable (see 4.7). Entering I]J in step
6 will cause the receiver to never allow access for the
transmitter(s) being programmed, while entering m in
step six will always allow access to the transmitters
being programmed.
When programming a block of transmitter numbers, the
receiver will emit a short beep every 3 seconds. Wait
until this beeping stops before proceeding with any
other programming. This may take up to 5 minutes
depending on the memory size and the number of
transmitters being programmed.
7.
Repeat steps 2 - 7 to enter additional transmitter numbers or
blocks of numbers, or press
m
together, or wait 20
seconds to end the programming sequence (beep).
4.3
DELETE A TRANSMITTER
1.
Press
I:!JllEI
and the four digit master code
I
]-U-I
(beep).
2.
Enter the two digit button number
QQ
then press
EI
(beep).
3.
Enter the four digit facility code
go.
IQ, then press
(beep).
4.
Enter the five digit transmitter number
g •
IGI-I
then press
EI
(beep).
5.
Repeat steps 2-4 to delete another transmitter, or press
m
together or wait 20 seconds to end the programming
sequence (beep).
4.4 DELETE ALL TRANSMITTERS
1.
Press
EIIII!!J
and the four digit master code
GJIOJG.JG]
(beep).
2.
Enter
It!l!EE
then press
EI
(beep).
This sequence will take about 1 1/2 minutes. The receiver will
sound a short beep about every 3 seconds, then one
long beep when the deletion is complete.
4.5 RELAY STRIKE TIME
1.
Press
r.:::I' ! :2l!l
and the four digit master code
1-IUrn
(be~).
2.
Enter the dasired strike time in seconds
GJGJ
then press
EI
(beep).
Valid strike timas are: 01 - 99
3.
Press
rnm
together or wait 20 seconds to end the
programming sequence (beep).
4.6 PROGRAMMING TIME & DAY
1.
Press
and the four digit master code
w-m:II;1
(beep).
2.
Enter the current hour and minute
I-I-no
then press
EI
(beep).
3.
Enter I]J for AM orm for PM then press
EI
(beep).
4.
Enter the current month
then press
EI
(beep).
5.
Enter the current day of the month
GJGJ
then press
EI
(beep).
6.
Enter the last two digits of the current year
GJGJ
then
press
EI
(beep).
7.
Enter the day of the week
g
then press
EI
(beep).
1
=
Sunday, 7 == Saturday
8.
Press
m
together or wait 20 seconds to end the
programming sequence (beep).
4.7
TIME ZONES
1.
Press r.::Jl!J!!] and the four digit master code
(beep).
2.
Enter the time zone number to be programmed
g
then
press
EI
(beep).
Valid time zone numbers are: 2 - 9
3.
Enter the beginning time in hours and minutas
lDt-n-1Q
then
prass
EI
(beep).
4.
Enter I]J for AM or
m
for PM then press
EI
(beep).
5.
Enter the ending time in hours and minutes
Glt-R I-I
then
press
EI
(beep).
6.
Enter I]J for AM or
m
for PM then press
EI
(beep).
7.
Enter the !ays of the week that the time zone is active
g IA-lmrJ
then press
EI
(beep).
Use the # key to skip days. For example,
if
the time zone is
ective
Mcm~
through Friday only, enter:
[! m
3' 4
filI!I!lL!J
8.
fiE!e.eat steps 2 - 7 to program additional time zones, or press
[[J[!I
together or walt 20 seconds to end the
programming sequence (beep).
4.8
PRINT MODE
1.
Press!L:Jl.!llIl and the four digit master code
(beep).
2.
Enter m to print transactions in real time mode or enter I]J to
not print the transactions In real tima mode, then press
EI
(beep).
In either case, transactions are stored in the buffer and can be
printed later.
If programming for real time print mode, printer
must be connected and turned ON, otherwise the
receiver
will
sound four long beeps.
3.
Press
m
together or wait 20 seconds to end the
programming sequence (beep).
4.9 CLEAR TRANSACTION BUFFER
1.
Press
and the four digit master code
~~.;J
(beep).
2.
Enter
li919@91 9
1then press
EI
(beep).
This sequence will take about 5 minutes. The receiver will
sound a short beep about every 3 seconds, then one
long beep when the deletion is complete.
4.10 PRINT TRANSACTION BUFFER
1.
Press
Ii.:E.Im
and the four digit master code
GJQGlQ
(beep).
The transactions stored in the buffer will print. The recei',
Jr
will sound a long tone when complete.
4.11 PRINT TRANSACTION FOR REQUESTED DATE
1.
Press
EJlt!Il!I
and the four digit master code
FI_' l FI_"""I["' I lII"""_1
(beep).
2.
Enter the month
rn
then press
EI
(beep).
3.
Enter the day
IG]G' J
then press
EI
(beep).
The transactions for the requested date will print. The
receiver will sound a long tone when complete.