DoorKing 8054-084 Handbuch
Blättern Sie online oder laden Sie pdf Handbuch für Empfänger DoorKing 8054-084 herunter. DoorKing 8054-084 4 Seiten. High security encrypted “rotating code” rf receiver
Seite drucken
MODEL 8054 MicroPlus
The model 8054 is a High Security Encrypted "Rotating Code" RF Receiver that is designed for stand alone applications. The
encrypted "Rotating Code" programming in this receiver and the companion MicroPlus
codes from being used again to access a controlled entry point. The 8054 receiver includes 10 time zones (eight programmable),
a history buffer that can store up to 2800 transactions in its memory. A serial printer can be connected to print the stored
transactions or the receiver can be programmed to print transactions in real time mode.
Installation
This receiver is NOT designed to be installed outdoors without being protected
from the weather. An outdoor enclosure is available for the receiver if required
(P/N 8057-110 - Metal Outdoor Box).
Install the 8054 receiver in a location so the antenna is NOT surrounded by
metal and is in free air as high as possible above the ground. A longer Coax
Antenna kit is available for the receiver if required (P/N 1514-073 - Includes
antenna, mounting "L" bracket and 15 feet of coax cable). An antenna amplifier
kit (P/N 8058-080) or a Yagi directional antenna kit (P/N 1514-072) is also
available for the receiver if required.
The RF LED on the side of the case will blink as RF energy is received.
If the LED blinks or is on continuously, this indicates that there may
be interference on the frequency (318 MHz) and short range may be
the result. If this happens, try relocating the receiver or remove the
source of interference. An antenna amplifier or a directional antenna
may be needed.
Note: Loop detectors and proximity card readers can cause receiver
interference.
Receiver Terminal Wiring
Stand-Alone Power and Device Wiring :
12-24 Volt
Connect 12 - 24 Volt AC or DC power to terminals #1 and #2. Use minimum 18 AWG wire to power the receiver.
Transformer
•
If DC power is used (Transformer): Terminal #1 is NEGATIVE and Terminal #2 is POSITIVE.
•
Connect the receiver relay contacts to the device to be activated.
- Receiver Terminal #3 is the relay contact Normally OPEN (N.O.)
- Receiver Terminal #4 is the relay contact Normally CLOSED (N.C.)
- Receiver Terminal #5 is the relay contact Common (C).
DC Polarity Matters!
To Receiver Terminal #1 (Neg.)
To Receiver Terminal #2 (Pos.)
To Printer
®
RF RECEIVER
8069
8070
Use ONLY MicroPlus
Printer:
Connect receiver directly to a printer using the printer interface terminal
as shown.
• Maximum wire run for printer data is 500 ft using Belden 9931, Consolidated
5324-CL or equivalent shielded wire. DO NOT use twisted pair wire for printer data.
• Serial printer setting: 9600 baud, 1 start, 8 data, 1 stop.
Printer
Cable
Not
Supplied
®
transmitters prevent copied transmitter
8071
8096
®
Transmitters
Removable
receiver terminal
for easy wiring.
#1 - Input Power
12-24 Volt AC, 12-24 Volt DC (Negative)
#2 - Input Power
12-24 Volt AC, 12-24 Volt DC (Positive)
#3 - Relay Contact (Normally Open)
#4 - Relay Contact (Normally Closed)
#5 - Relay Contact (Common)
#6 - Printer Data
(
P1 DoorKing Printer Interface Terminal)
#7 - Printer Signal Ground
(
P2 DoorKing Printer Interface Terminal)
#8 - Printer Busy
(
P3 DoorKing Printer Interface Terminal)
To Receiver Terminal #6
P1
To Receiver Terminal #7
P2
To Receiver Terminal #8
P3
Printer Interface Terminal P/N 1587-010
DoorKing Part Numbers
8054-081
50 Transmitter Codes
8054-082
100 Transmitter Codes
8054-083
250 Transmitter Codes
8054-084
500 Transmitter Codes
8054-085
1000 Transmitter Codes
8054-086
1250 Transmitter Codes
R e
D
c e i
L E
T e r
R F
v e r
m i
n a
e
o d
l
r C
n
t t o
s t e
B u
e )
M a
p a g
e x t
e n
( S e
Terminals 3-4-5
rated for 30 volt,
1 amp max.
(Included)
120 S. Glasgow Avenue
Inglewood, California 90301
18"
Coax
Cable
Coax
Antenna
Kit
U.S.A.