Flying Industry Development 0020736 Kurzanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Kurzanleitung für Fernsteuerung Flying Industry Development 0020736 herunter. Flying Industry Development 0020736 3 Seiten. Rf wireless remote control kit

Seite drucken
Usage:
The receiver can be used to control DC 6V / 9V / 12V / 24V equipments. If the power supply of those equipments is DC 12V, you should choose the
receiver with same DC 12V version; and if the power supply of those equipments is DC 24V, you should choose the receiver with same DC 24V
version.
Wiring:
If you want to control a DC 12V lamp, do as following:
1) Connect the positive pole of DC power supply to terminal "L / +" of INPUT, and connect the negative pole of DC power supply to terminal "N / -" of
INPUT.
2) Connect the positive pole of lamp to terminal "L / +" of OUTPUT, and connect the negative pole of lamp to terminal "N / -" of OUTPUT.
Setting different control modes：
Setting different control modes (We have set the receiver as Toggle control mode before delivery. If you want to use other control modes, do as
following operation):
Setting control mode Toggle: Only connect Jumper-2.
Control mode Toggle (with transmitter CP-15): Press -> On; Press again -> Off.
Press button 1 of the transmitter: Output terminal of the receiver 1 outputs DC power, the lamp 1 is on.
Press button 1 again: Output terminal of the receiver 1 stops outputting, the lamp 1 is off.
...
Press button 15 of the transmitter: Output terminal of the receiver 15 outputs DC power, the lamp 15 is on.
Press button 15 again: Output terminal of the receiver 15 stops outputting, the lamp 15 is off.
Setting control mode Momentary: Only connect Jumper-1.
Control mode Momentary (with transmitter CP-15): Press and hold -> On; Release -> Off.
Press and hold button 1 of the transmitter: Output terminal of the receiver 1 outputs DC power, the lamp 1 is on.
Release button 1 of the transmitter: Output terminal of the receiver 1 stops outputting, the lamp 1 is off.
...
Press and hold button 15 of the transmitter: Output terminal of the receiver 15 outputs DC power, the lamp15 is on.
Release button 15 of the transmitter: Output terminal of the receiver 15 stops outputting, the lamp15 is off.
Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Control mode Latched (with transmitter CP-15): Press -> On, Press another button -> Off.
Press button 1 of the transmitter: Output terminal of the receiver 1 outputs DC power, the lamp 1 is on.
Press other button of the transmitter: Output terminal of the receiver 1 stops outputting, the lamp 1 is off.
...
Press button 15 of the transmitter: Output terminal of the receiver 15 outputs DC power, the lamp15 is on.
Press other button of the transmitter: Output terminal of the receiver 15 stops outputting, the lamp 15 is off.
Wired control terminals:
The receiver has manual control terminals, you can connect external devices, sensors, or manual switches to control the receiver.
1) Signal input:
You can connect external devices (with low level output signal) to manual terminals 1 (Signal -) and terminal 2 (Signal +), then the external device's
output signal can control the receiver.
When the external device outputs low level signal to manual terminal 1 and terminal 2, turn on the relay. Output terminal outputs DC power, the lamp
is on.
When t
he
external
device
stops
to output
signal, turn off the relay. Output terminal stops outputting, the lamp is off.
2) The manual switches:
You can connect manual switch to terminals 1 and 2, and then you can use this manual switch to control the receiver.
When connect terminals 1 and 2, turn on the relay. Output terminal outputs DC power, the lamp is on.
And when disconnect terminals 1 and 2, turn off the relay. Output terminal stops outputting, the lamp is off.
How to pair the transmitter to the receiver:
1) Press the learning button of receiver for 1- 2 seconds; signal LED on the receiver is on. The receiver enters into status of LEARNING.
2) Press any one button on transmitter. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.
4) The receiver can learn several remote controls with different codes.
Delete all transmitters:
We have learned remote control to the receiver. If you don't want the receiver to work with the remote control, you can delete all codes of remote
controls, which are stored in the receiver.
Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored
codes have been deleted successfully.
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com