Daema DWF-7688KG Benutzerhandbuch - Seite 6

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Waschmaschine Daema DWF-7688KG herunter. Daema DWF-7688KG 10 Seiten.

Seite drucken

Installation and

adjustment

Please install and adjust the machine according to the requirements of the manual.

It is very important to your safety and correct operation.

Unpacking

Unpack the carton and take out the bottom panel.

Open the top lid of washing machine and take out all of the accessories.

Remove all wrappers, including the polystyrene base.

You are advised to keep all the packaging for reuse in case the machine is to be

transported again.

Installing the bottom cover

Please lean the machine forward gently, and insert the

the bottom cover (the side with instructions) into the notch

along arrowhead direction.

Fix the bottom cover on the washing machine base with

two tapping screws in the accessories by using cross

screwdriver.

Positioning

The distance between the washing machine and the wall should be more than 50mm, and the

maximum allowed angle of the shank base of the machine is 1.The slanting or rough ground may

cause operating stopped or unstable, please adjust it with the following methods:

Make it horizontal

Use a tied thread with plumb to check

if it is horizontal.

Adjust the adjustable foot

1、Lift up the adjustable foot gently, loose the adjustable nut

and twist the adjustable foot.

2、Fasten the nut after adjustment.

Notch

Bottom panel

。

Adjustable

nut

Fasten

Adjustable

Loosen

foot

High

Low

Maintenance

Maintenance methods

After the end of the programme

The machine stops automatically ,and music

buzzer will remind you to take out the laundries

or start again.

Once you have finished using the machine,

you are advised to unplug it and turn off the

water taps to avoid unexpected leak or fire.

External cleaning

Clean the exterior cabinet of the appliance with

soft cloth. Do not use cleanser, volatile chemical

materials to clean the machine, which will

damage plastic parts and the surface.

Clean inlet gate

It is possible that the inlet filter net can be blocked

by the dust, please clean it according to the follow

steps:

1. Close the tap and turn on the power switch.

2. Start the washing machine for 5 seconds(make

the water in the inlet hose flows to the tub),and

cut off the powersupply.

3. Pull off the inlet hose, remove and clean the

inlet valve and the inlet net, and install again.

1.Once you have using the machine, you are advised to turn off the water taps.(if necessary,

pull out the inlet hose)

2. Do not keep water in tub for a long time. When washing is finished , drain it right away.

3.Once you have finished using the machine, you are advised to unplug it.

4. Put the electric cable and the drain hose in order.

5. Wipe the water on the surface and in tub with soft cloth and keep the top lid opening for a

while. It helps to prevent mould and stagnant smells forming inside the appliance.

If the water in the inner tub has possibility to freeze,please do like below:

1. In winter, if remaining water freeze can cause the washing machine trouble,

please take off the water inlet hose and drain out the water in the hose and inner tub.

2. If the water freeze, please don't operate the washing machine. Put 40℃ hot water

in the tub, the hot water should submerge the pulsator, after a few minutes, rotate

the pulsator by hand gently, then you can operate the washing machine.

Clean the lint filter

It is necessary to use lint filter during washing.

After washing, please clean the lint filter in time.

Clean the lint filter according to the

following steps:

1. Pull out the lint filter.(see

llustration 1)

2. Open the lint filter and wash it.(see

llustration 2)

3. Close the lint filter and install it to

proper position.

Press it and pull out the lint filter

Open

The baffleplate

(the black rubber block)

Illustration1

Illustration2

Open