Dorex 1701 Series Einbauanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Einbauanleitung für Türöffnungssystem Dorex 1701 Series herunter. Dorex 1701 Series 3 Seiten. Door closer with slide track arm

Seite drucken
PULL SIDE – TOP JAMB INSTALLATION
(MAXIMUM 120° DOOR OPENING)
1 3/4
B
(44.5)
3 5/8
(92)
5 9/16
(141)
A (2x) : Drill ¹⁄8" (3 mm) pilot hole for wood screws or drill & tap for #10-32 machine screws
B (4x) : Drill ³⁄16" (4.75 mm) pilot hole for wood or drill & tap for 1/4-20 UNC machine screws.`
INCH
(MM)
HINGE
CENTERLINE
1. Locate door closer and track position using the Figure 1 above.
2. Mark hole positions and drill holes as indicated above.
3. Install door closer to the frame (or drop plate) using the appropriate fasteners as per supplied instructions with door closer and/or drop plate.
The POWER ADJUSTMENT valve of the door closer should be facing the hinges.
4. Assemble track stopper (or holder) and slide insert as indicated on page 1, then fasten to the door using supplied wood or machine screws.
5. Place arm on door closer top pinion at pre-load postion parallel to the door in Figure 2. Then secure with included arm washer and socket bolt.
6. Rotate arm towards the door, then secure arm end to the slide insert in the track with supplied screw.
7. Open the door to the desired opening angle then slide the stopper (or holder) against the slider insert. Secure the stopper (or holder) into position
by tightening the set screw.
8. Release the door and verify operation. Adjust door closer power and closing speeds as indicated on the door closer's installation instructions.
PUSH SIDE – TOP JAMB INSTALLATION
(MAXIMUM 110° DOOR OPENING)
9 1/16
(230)
B
DOREX 1701
9/16
(14.3)
FRAME
A
EDGE
3
(76)
A (2x) : Drill ¹⁄8" (3 mm) pilot hole. Use self-tapping screws.
B (4x) : Drill ³⁄16" (4.75 mm) pilot hole or drill & tap for 1/4-20 UNC machine screws.
INCH
(MM)
DOOR CLOSER AND TRACK MUST BE LEVELED HORIZONTALLY.
HINGE
CENTERLINE
1. Locate door closer and track position using the Figure 1 above.
2. Mark hole positions and drill holes as indicated above.
3. Install door closer to the frame (or drop plate) using the appropriate fasteners as per supplied instructions with door closer or drop plate.
The POWER ADJUSTMENT valve of the door closer should be facing AWAY from the hinges.
4. Assemble track stopper (or holder) and slide insert as indicated on page 1, then fasten to the door using self-tapping screws.
5. Place arm on door closer bottom pinion horizontally as shown in Figure 2. Then secure with included arm washer and screw.
6. Rotate arm towards the door, then secure arm end to the slide insert in the track with supplied screws.
7. Open the door to the desired opening angle then slide the insert (or holder) against the slide insert. Secure the stopper (or holder) into position by
tightening the set screw.
8. Release the door and verify operation. Adjust door closer power and closing speeds as indicated on the door closer's installation instructions.
Installation Instructions
1701 SERIES DOOR CLOSER WITH SLIDE TRACK ARM (SA1901)
9 1/16
(230)
DOREX 1701
SA1901
A
(504.8)
POWER
ADJUST
DOOR CLOSER AND TRACK MUST BE LEVELED HORIZONTALLY.
3/4
(19)
SA1901
19 7/8
(504.8)
POWER
ADJUST
1701-DP
Drop plate may
be required.
3/4
(19)
19 7/8
DRAWING IS NOT TO SCALE.
DO NOT USE AS TEMPLATE.
1701-DP
Drop plate may
be required.
2 3/16
1 5/8
(55.6)
(41.3)
DRAWING IS NOT TO SCALE.
DO NOT USE AS TEMPLATE.
Right hand door installation shown.
For left hand installation, reverse illustrations.
DOOR
EDGE
7/16
(11)
FIGURE 2
Main Arm
FIGURE 1
Right hand reversed door installation shown.
For left hand reversed installation, reverse illustrations
FRAME
EDGE
DOOR
STOP
FIGURE 2
Main Arm
FIGURE 1
2 3/16
(55.6)
2
(50.8)
Reveal
SA1901-1701-INS
RIGHT HAND
RIGHT HAND
REVERSED
Frame Transom
9/16
(14.3)
1 5/8
(41.3)
2023/12
2/3