Dot-Spot clarios-mini Benutzerhandbuch - Seite 12

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für DJ-Ausrüstung Dot-Spot clarios-mini herunter. Dot-Spot clarios-mini 15 Seiten.
Auch für Dot-Spot clarios-mini: Benutzerhandbuch (20 seiten)

Seite drucken

Assembly

The switching point of the luminary between on and off for the PWM level is not defined: Ideally it

should be worked with a switching impulse between ground and open contact or optionally with an

impulse between ground and operating voltage. A PWM signal differing from the operating voltage

is not allowed.

Free cabling

The connection is made according to the assignment tables. The connection must be carried out

according to the required IP classification.

clarios-mini white / monochromatic

Wire color

red

blue

black

Attention:

In case the luminary is used without the dimming function, the PWM line (wire for the

PWM signal) must be connected to ground (-). Otherwise the LED remains off.

Connection diagram of the clarios-mini white / monochromatic without dimmer

See respective drawing in the middle of this manual (p. 14).

Connection diagram of the clarios-mini white / monochromatic with dimmer

See respective drawing in the middle of this manual (p. 14).

clarios-mini RGB

Wire color

white

red

green

blue

black

Attention:

The cable of the clarios-mini RGB features a wire which is not used (brown or gray).

Normally, the wire is shortened ex works and should not be connected.

Connection diagram of the clarios-mini RGB

See respective drawing in the middle of this manual (p. 15).

Assignment

+ 12 Volts

S-PWM

ground (-)

Assignment

+ 12 Volts

red S-PWM

green S-PWM

blue S-PWM

ground (-)

Assembly

M12 plug and cabling system

The connection of the clarios-mini versions with M12 connector is quite simple, either with or

without dimming function. Plug the connector of the luminary in a free socket of the M12 cabling

system. The M12 cabling system is coded in a way to avoid wrong wiring or failures.

Please plan the components required for the electrical installation (power supplies, distributors,

extensions and plugs for unassigned M12 sockets) according to the sales documentation of the

M12 cabling system before placing an order.

Assignment of the M12 connector system

Pin number

Wire color (if plug

5-pin plug clarios-mini

M12 plug

is pinched off)

white / monochromatic

brown

S-PWM

white

blue

12 V +

black

green/yellow (gray)

ground (-)

Operation

LED lights are extremely energy efficient and, under normal operation, have a very long life. To

ensure the maximum life of the LED and to increase the energy efficiency, the following should be

considered:

■ The turning on and off of the luminary should be carried out by the input circuit of the power

supply.

■ The turning off of the luminary via the PWM signal should not occur permanently since in this

case the electronics unit of the luminary continues operating.

■ Even if the luminary is equipped with a THERMOPROTECT system that protects the luminary

against thermal damage, a permanent abnormal operation should be avoided.

■ The heat dissipation of the LED must not be hindered. Therefore, do not cover the spot.

■ Avoid operating the spot in case of direct solar radiation.

■ In automatic mode, control the spot via timer and / or twilight switch.

Maintenance, disposal

Care

■ Clean the spot with a damp cloth every now and then.

■ The luminaries are made of stainless V4A steel. However, depending on the environmental

conditions and the surfacing material, the metal parts may present the so-called flash rust, but

this does not constitute a defect. Flash rust can be removed easily with appropriate stainless

steel cleaners. Flash rust is particularly likely when the housing comes into contact with ferrous

particles (e.g. iron and grinding dust, ferrous plant fertilizers or the like).

5-pin plug

clarios-mini RGB

red S-PWM

green S-PWM

12 V +

blue S-PWM

ground (-)