Double K Industries Challeng Air AIRMAX Gebrauchsanweisung - Seite 2

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Hochdruckreiniger Double K Industries Challeng Air AIRMAX herunter. Double K Industries Challeng Air AIRMAX 4 Seiten. Animal dryer

Seite drucken
IMPORTANT SAFEGUARDS
WARNING: IMPORTANT SAFETY PRECAUTIONS! PLEASE READ
COMPLETELY BEFORE USING PRODUCT!
When using electrical appliances, especially in the presence of children and animals, basic
safety precautions should always be followed to reduce the risk of re, electric shock, and
personal injury, including but not limited to the following:
DO NOT TURN ON DRYER WITHOUT FIRST HOLDING THE DRYER HOSE, as the air volume from
the dryer can cause the hose to whip or move rapidly and may cause injury.
1.
Do not leave dryer OR the animal unattended while product is in use.
2.
Unplug unit when not in use.
3.
Do not use extension cords with dryer.
4.
Do not unplug unit by pulling on cord.
5.
Do not expose dryer to rain or water.
6.
Do not use or store dryer where it can fall or be pulled into tub or sink or standing water.
If dryer falls into water . . . UNPLUG IT . . . Do not reach into the water!
7.
Unplug unit before attempting any maintenance or service.
8.
Do not put any object into dryer openings.
9.
Keep loose clothing, jewelry and hair away from dryer openings.
10.
Do not direct dryer air towards eyes or ears of people or pets.
11.
Never use dryer if it has a damaged cord or plug, has been dropped, damaged or
exposed to rain or water. Return to Double K Industries or an Authorized Service
Center for service.
12.
This dryer should not be used as a cage dryer, for cage drying please consider our model
560 Cage dryer.
13.
This product is for use on animals only.
14.
Recommended operation by adults only. Use caution when working around children.
15.
Do not use attachments not recommended by Double K Industries.
16.
Do not operate without lters in place. Keep lters clean, as dirty lters limit air intake
and may damage the motor or cause overheating.
17.
Plug only into a properly grounded receptacle. Always make sure the amperage of the
electrical outlet is su cient for the amperage rating of the product. (See Product Speci -
cations for amperage rating of this product).
18.
Do not use product for anything other than its intended purpose.
19.
Do not attempt to perform any service or maintenance not outlined in instruction
manual.
20.
Do not attempt any product modi cations or alterations. Do not use, if any parts or
switches are damaged. Send to an Authorized Service Center or Double K Industries
for service.
21.
When servicing, use only Double K Industries parts.
WARNING: DISCONNECT POWER SUPPLY BEFORE SERVICING
AVERTISSMENT: COUPER L'ALIMENTATION AVANT
L'ENTRETIEN ET LE DÉPANNAGE
2
BRUSHES
Your CHALLENGAIR AirMax® has two brush-type motors. The brushes should be checked for
wear after approximately 500 hours of use. If the carbon brushes are worn shorter than 1/4
inch, the brushes should be replaced. Brushes may be ordered from Double K Industries or
an Authorized Service Center (you will need 2 sets, 1 set for each motor). Please be sure to
specify that your dryer is an AirMax®, as the brushes are slightly di erent from one dryer
model to another.
To check and/or replace brushes:
1.
Unplug electrical cord from wall outlet.
Disassembly:
2.
Slide o the back cover from the dryer. This is a compression t and will come o with a
little e ort.
3.
Remove all screws on the outside of the dryer that hold the two halves of dryer housing
in place. Remove the o-ring on the snout of the dryer. It may be best to lay the dryer on
its side while removing these screws. Lift o the top half.
4.
Each motor will be sitting in place inside the rubber silicone motor mounts. Removing
the rubber silicone motor mounts from the motor is not necessary to replace brushes.
5.
Disconnect the motor power wires. Note where wires connect.
6.
Front motor:
A. Loosen the two brush assembly retainer screws (Fig. 3, Ref # 3) to loosen the
brush assembly retainer (Fig. 3, Ref # 2). Remove the brush assembly (Fig. 3, Ref
# 1) and replace it with a new one. (Note: IMPORTANT - the brush has a small
tab on the bottom that MUST be tted into the slot on the motor frame for
proper positioning) (Fig. 3, Ref # 4)
B. After the new brush assembly is seated, tighten the brush assembly retainer
screws.
C. Repeat steps A-B for the brush on other side of motor.
Rear motor:
A. Follow steps A-C above, as outlined for the front motor.
Reassembly:
7.
Inspect the motor mounts for cracks or damage -- replace if necessary. Set the motors
back into their original positions in the dryer housing. Each motor mount has slots that
t over corresponding alignment tabs on the inside of the dryer housing. These slots
and tabs must match up for proper t and function. (Note: In the event that the motor
mount is removed from the motor, simply replace it by being mindful to align the
contours of the motor mount with corresponding contours on the motor housing.)
8.
Reattach the screws around the outside of the dryer making sure the two halves are
matching up.
9.
After the two halves of the dryer housing have been put together, replace motor lter on
back motor and push the back cover onto the rear of the dryer. Replace exterior lter
onto back cover. Always make sure all lters are in place before operating dryer.
Replace o-ring on snout.
7