AMPHIBICO PHENOM NX5 SE Gebrauchsanweisung - Seite 12

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Kamera-Zubehör AMPHIBICO PHENOM NX5 SE herunter. AMPHIBICO PHENOM NX5 SE 14 Seiten. Video camera housing sony hxr-nx5 & sony hdr-ax2000

Seite drucken

INSTALLING ACCESSORIES

The PHENOM as been equipped with mounting holes and

railing systems to accommodate for a variety of accessories.

Locations for a few of these accessories have been

designated for your convenience. However, these locations

can be used for other accessories. Some accessories like

the monitor or video lights require to be connected to the

housing. Accessory connector ports (one on the

right side and two on the left side) are available

for this purpose.

Use Allen key (supplied) to tighten handle

Achieving neutral buoyancy and balance

Adding accessories to the housing may make it

heavier or off balance in the water. Removable

ballasts have been added to the bottom of the

housing for this purpose.

To make the necessary weight adjustments.

1. Submerge the housing with the added accessories

into the water so you get an idea of what and where to

remove weight.

2. Using the Allen key supplied, start removing or

relocating the ballasts from the right or the left channels

as illustrated.

WATER ENTRY

1. Always turn housing to its ON position before entering

water. To turn it ON, use the right grip trigger button. This is

confirmed by the CAM. indicator light turning on steady

green. The camcorder viewfinder will also turn ON.

Doing step 1 will activate the built-in moisture alarm sensor

located in the bottom of the housing.

IMPORTANT

The right lights on both grips will start flashing RED if

water leakage occurs inside the housing. Remove from

water as soon as possible, take the camcorder out of the

housing and inspect all seals and the inside of the

housing. ALWAYS REMEMBER DIVER SAFETY FIRST.

2. Lower the housing just below the water surface in level

position and hold for one minute to confirm there is no

leakage in the housing.

Never leap into the water while holding the housing. Always

have the housing handed to you or lowered down once you

are in the water.

3. Point the lens of the housing upwards and shake off any

air bubbles. It may also be necessary to gently wipe the lens

with your finger to remove bubbles.

PREPARING CAMCORDER & HOUSING

"T" bracket

Monitor bracket

Video lights

Carry handle (supplied)

Accessory

connector port

Allen key (supplied)

Ballast

Left Grip

Right Grip

Trigger Button

The PHENOM offers a large range of electronic

functions. This chapter will explain to you in detail all of

these functions.

POWER ON

The camcorder should be powered ON by default after

inserting it into the housing. In the event that it's not, the

trigger button on the right grip will activate the camcorder.

Simply press on it once and the CAM indicator light will turn

on steady green and the rear viewfinder will also be turned

on to confirm the power ON of the camcorder.

POWER OFF

To power off the camcorder during a dive will allow you to

save on battery energy. To do so, push and hold the left grip

trigger button while pressing down on one of the control

panel switch as indicated.

CAM MODE

The housing will set itself to record/standby mode (CAM

indicator LED is steady green) when initially turned ON. To

record a scene, simply press on the right grip trigger button.

The CAM indicator LED will flash green when recording.

Pressing it again will bring it back to record/standby mode.

WARNING

The CAM indicator LED will light steady amber as a warning

that there is no recording media present in the camcorder.

Inserting a memory card or flash memory unit will bring back

the indicator light to steady green.

HOUSING & CAMCORDER OPERATION

Power ON

Right grip trigger button

Left Grip

Trigger button (shift key)

Power OFF

Control panel switch

Record/Standby

Right grip trigger button