AmpliVox SW124 Betriebsanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Rednerpult-System AmpliVox SW124 herunter. AmpliVox SW124 2 Seiten. Ampli-pod tabletop podium

Seite drucken
Assembly oF Gooseneck mic:
To install the 1. FLEXIBLE GOOSENECK onto the 2. MOUNTING
FLANGE located by the far left corner of the desktop reading surface,
first turn the neck piece clockwise onto the mount. Next install the
microphone holder (U shaped piece) onto the end of the gooseneck
by turning it clockwise onto the top of the neck. You can then slide
the 3. MICROPHONE into the 4. SHOCK MOUNT MIC HOLDER as
shown.
The 5. MIC CORD has a plug with three small holes in one end, A for
connecting with the microphone, and a ¼ in. male plug on the other
end, B for connecting with the unit on the control panel. Connect
the end with the three holes to the base of the microphone, and
plug the male ¼ in. end of the microphone cord into the jack labeled
DYNAMIC. The microphone has an ON/OFF switch. it should always
be in the OFF position until the main power is ON and you are ready
to speak.
MAIN POWER SWITCH
The 6. MAIN POWER switch is located on the control panel. Flip the
rocker switch to the ON position. The red light next to the switch will
light up showing that the power is on.
DC INPUT
Connection for an optional external power adapter.
POWER CORD / AC ADAPTER
Included is an AC adaper for powering the Ampli-Pod Podium PA
and recharging the internal SLA battery. You can run the Ampli-
Pod Podium PA on the AC adapter from a standard wall plug and
recharge the SLA battery but the best and fastest charging occurs
when the unit is not on.
IMPORTANT PLEASE READ
The SS124 and SW124 come with an SLA (Sealed Lead Acid)
battery fully charged and ready to go with a run time of 30 hours.
Also included is the S1460 International AC Adapter/Recharger
(110/240V; 50/60Hz) so you can recharge the SLA battery. The
battery is not user accessible.
BUILT-IN HANDLES -
DURABLE MOLDED PLASTIC
WHEN TRANSPORTING UNIT,
USE BOTH HANDLES
SHOWN WITH STORAGE SPACE OPEN
SPEAKER
ss124 / sw124
SHOWN: CONTROL PANEL FOR
SW124 WITH OPTIONAL 2ND WIRELESS
3. MICROPHONE
4. SHOCK MOUNT MIC HOLDER
1. FLEXIBLE GOOSENECK
5. MIC CORD A
2. MOUNTING FLANGE
6. MAIN POWER
7. VOLUME
THE GRILLE IS MAGNETICALLY ATTACHED -
SPEAKER
PULL SPEAKER GRILLE OFF
AT BOTTOM INDENT TO ACCESS STORAGE AREA
2
ss124 & sw124 conTRol pAnel
WRLS 2
ON
LAMP
ON
ON
OFF
B
A
OFF
OPTIONAL
INTERNAL
READING
WIRELESS MIC
LAMP
RECEIVERS
N011--35
SWITCH
124 panel label
3.3 h x 11.45 w
white on PMS 432 grey with PMS 300 Blue
make sure AV knocks out to white
INTERNAL WIRELESS MICROPHONE RECEIVER *SW Model only*
Power 'ON' and 'OFF'; Frequency 'A' and 'B' switches. Frequency should
match wireless transmitter. The red light above these switches will
come on when the wireless microphone receiver is active. In SW124
models equipped with two receivers, each one has its own power switch
and frequency switch.
WIRELESS MIC SET UP
The VHF wireless microphone system is compact, lightweight and
compatible with all AmpliVox VHF wireless systems. The wireless mic
operates in an authorized VHF band and has a useful range of up to
200-ft. in line-of-sight applications. Each system operates on two crystal-
controlled, switch selectable frequencies for clear clean transmission.
"A" Channel
"B" Channel
5. MIC
T6: 171.105
MHz T7: 171.845 MHz
CORD B
The frequency appears on the back of each unit. Both transmitter and
receiver must have the same, and both units must be set to either "A" or
"B." Note that two transmitters on the same frequency will not work with
one receiver. However two or more receivers will work with the same
transmitter. Before use, make certain you understand the function and
operation of the system.
RIBBON FOR
BATTERY REMOVAL
BATTERY COVER
RF INTERFERENCE
Please note that wireless frequencies are shared with other radio
services. According to the Federal Communications Commission
regulations, "Wireless microphone operations are unprotected
from interference from other licensed operations in the band. If any
interference is received by any Government or non-Government
operation, the wireless microphone must cease operation..." If you need
E X T E N D Y O U R V O I C E W I T H
WRLS 1
ON
POWER
MICROPHONES
ON
ON
MAIN
OFF
B
A
ON
VOLUME
DYNAMIC
OFF
2
DC IN
AUX OUT
CONDENSER
WIRELESS
MAIN
MASTER
MIC
POWER
VOLUME
INPUT
SWITCH
POWER
AUX
MIC
INPUT
OUT
INPUT
assistance with operation of frequency selection, please contact your
dealer or AmpliVox. Additionally There are models available for use in
Canada.
POWER SOURCE
The transmitter and receiver are each operated by a 9V alkaline battery.
Before use, install a battery as shown. Make certain the battery is fully
seated in its compartment so the cover slides in place easily. Battery life
with alkaline batteries is approximately 8 hours of operating time. The
receiver also features an external jack for connecting a 9V DC power
supply (not included).
TRANSMITTER
CHANNEL SELECTOR SWITCH
TRANSMITTER OPERATION
If there is a "dead spot" in a room, try a slight change of position or try
changing frequencies. Each unit provides two selectable transmitting
frequencies.
1) Switch the Frequency Selector Switch to the desired channel
(A or B).
9V DC ALKALINE
BATTERY
2) Belt clip on the back of the unit clips the transmitter onto a belt or
the transmitter simply can be put into a pocket.
3) Plug the microphone into the Mic Input Jack.
4) The microphone can be clipped to a necktie or other clothing, using
the supplied clip.
5) Slide the power ON/OFF switch to
the ON position (the LED indicator
light will illuminate).
3
1-800-267-5486
WWW.AMPLI.COM
MADE IN USA
AUXILIARY
OUTPUT
1
VOLUME
TONE
L - SPEAKER - R
3
LINE IN
LINE OUT
AUXILIARY
TONE
SPEAKER
VOLUME
CONTROL
jACKS
MIC
LINE IN
LINE OUT
INPUT
jACK
jACK
MIC INPUT jACK
POWER ON INDICATOR
POWER ON/OFF SWITCH
Need help?
call 800-267-5486
or 847-498-9000
email:
customerservice@
ampli.com
ss124 / sw124