DP 21-4000 Handbuch für den Besitzer - Seite 5
Blättern Sie online oder laden Sie pdf Handbuch für den Besitzer für Laufband DP 21-4000 herunter. DP 21-4000 9 Seiten.
Storage and Maintenance
The PRIME FIT
TM
TREADMILL can be moved and stored quite easily. Simply keep it in a .cle.an,dry, and convenient place, if
FREADMILL iSto be stored for more _an 30 days, it iS I_est to remove BATTERiES (Not Inczu_ed) from MONITOR(No.
2). The
:_ EADMILL should require little actual maintenance other _an perk_dtcallyspr.aymg a silicon |ut_flcantunder TR EADBELT (No.
):8), Keep TREADMILL clean to avoid deterioration of TREADBELT and ftnisn,
t'he TREADBELT
(No. 128) has been factory pre-adjusted. However, if it shifts to one side or the other, follow these steps to
readiust i t.
1, If TREADBELT has moved to dght, tlghten doht ADJUSTMENT
BOLT (No, 133) 1i2 turn while TREADMILL is running and
no one ts on it. The TREADBELT should move towards left.
2. Let TREADMILL run several turns of TREADBELT
and note any sideways movement.
3, If only a small amount of ¢ttange occurred, loosen I_ft ADJUSTMENT BOLT (No. 133) 1/2 turn.
4. Repe=tt step 2.
Repeat steps i _mugh 4 until TREADaELT
is centered and remalns there dudng use, If TREADEELT has moved to LEFT, fop
low steps 1-4 but start wtttl LEFT side.
-
_:
if TREADaELT
is slipping it will be necessary to ttg_en both ADJUSTMENT BOLTS until slipping has stopped, it may
then be necessary to repeat steps 1 tl_mugt_4 for alignment.
CAUTION: DO NOT OVERTIGHTEN TREADBELT.
Otertlgh'tenin_ Is denoted by Curling of the edges of the TREADBELT.
IF NO SPEED OR DISTANCE is displayed on MONITOR (No. 2) check the following:
i, The wine of REED SWITCH (No. 136) ftorn CONSOLE (No, i02) isplugged into the MONITOR (No. 2).
2. The BATTERIES are not weak or dead,
3. The REED SWITCH (No. 136) and MAGNET on the FRONT ROLLER (No. 126] =ireIn the correct position, it may be neces-
sary to te=llgn the REED SWITCH with the MAGNET, Follow these steps to realign it:
a,
_.._:
Unplug the TREADMILL.
MAGNET
i/8"
b,
Remove MOTOR COVER (No. 123) - see Rgure 5,
c.
Check spacing and allcjnrnent between MAGNET on left side of FRONT ROLLER
(,NO,t28) and REED _WlTCH (NO. 136) on the TREAOMILLFRAME
(No. 110)-
see FIGURE 3. The, spacing must be 1/8" and the edge of the REED SWITCH
|
be aligned w_h the center of the MAGNET.
Move REED SWITCH on
TREAOMILL_ FRAME,
_:
1/8" is equal to the thickness of two pennies.
d,
Reattach MOTOR COVER (No. 123).
l=
BATTERIES: Use four "AA" batteries to power MONITOR
(No. 2). It is recommended
that alkal{_e batteries be used for longer battery life. Rechargeable batteries ate not recom-
mended. TO extend battery life, turn MONITOR
off after use.
SWITCH
.................
'
136
FOR ANSWERS TO ANY OTHER MAINTENENCE
QUESTIONS CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
FOR SERVICING
RECOMMENDATIONS.
SEE PHONE NUM8ERS ON FRONT PAGE.
FIGURE 3....