CardAccess Z2IR10A-ZP-10P Installationshandbuch

Blättern Sie online oder laden Sie pdf Installationshandbuch für Kontrolleinheit CardAccess Z2IR10A-ZP-10P herunter. CardAccess Z2IR10A-ZP-10P 2 Seiten. Zigbee-to-ir module

Seite drucken

ZigBee-to-IR

Module

Installation

Guide

Put MORE Automation in

Home Automation.™

Features

The Card Access Z2iR ZigBee-to-IR Module is a wireless ZigBee interface

with two independent IR emitter ports. It is powered from any 5V USB

2.0-compliant port supplying continuous power (even when the device with

the USB port is turned off). The Module can connect any IR device into a

Control4 home automation environment. The Z2iR Module also operates as

a ZigBee

(IEEE 802.15.4) parent-rounting node which can improve ZigBee

mesh density and footprint-often solving ZigBee problems when devices are

installed on the edges of a mesh network.

Supported Models and Requirements

This documentation applies to the following Card Access products

Z2IR10A-ZP

ZigBee-to-IR Module (single pack)

Z2IR10A-ZP-10P

ZigBee-to-IR Module (10 Pack)

Important Safety Instructions

WARNING! You should install this device in accordance with all

national and local electrical codes.

IMPORTANT! This product is not intended for direct connections to

AC mains (120V/220V). Refer to specifications.

IMPORTANT! Improper use or installation of this device can result

in LOSS OF/DAMAGE TO PROPERTY.

IMPORTANT! Using this product in any manner other than outlined

in this document voids your warranty. Also, Card Access is NOT

responsible or otherwise liable in any way for any damage resulting

from the misuse of this product. See the section of this document

entitled WARRANTY for details.

What Is Included

• Bubble bag containing one (1) Wireless ZigBee-to-IR Module

• Installation Guide / Product Warranty / Product Registration Document

• Two (2) True IR Emitters

• One (1) 5V DC Mini USB Power Supply Module

• One (1) Mini USB 2 Meter Cable

• One (1) Dual-Stick Adhesive Strip

Specifications

Power Source:

5VDC Power Supply

Power Usage:

100mA at 5VDC, fully active

Device Temperature Range: Operational -20°F to 158°F (-28°C to

70°C)

Humidity 5% to 95% Non-Condensing

Storage -20°F to 158°F (-28°C to 70°C)

Dimensions (LxWxD):

2.80"(L) x 1.75"(W) x 0.57(D)" (77.1mm x

44.5mm x 14.4mm)

Communications:

ZigBee (IEEE 802.15.4) 2.4 GHz,

15-channel, spread spectrum radio

Installation

Place the ZigBee-to-IR Module in a location which ensures:

• Easy access to a power outlet

• Close proximity to the device(s) to be controlled

NOTE: Make sure the ZigBee-to-IR Module gets good ZigBee

wireless reception by:

• Ensuring it is within 150 feet of another ZigBee device.

• Ensuring the device is not installed by other electrical equipment

that may cause interference with the ZigBee signal (such as some

cordless telephones or other devices that operate on the 2.4 GHz

frequency).

• Avoiding exposure to extreme environmental conditions.

Download the Z2iR DriverWorks Driver using Composer's

Online Driver Database or from the Card Access web site: www.

cardaccess-inc.com/automation/drivers. (Copy the Driver to the

"Control4 / Drivers" folder on your PC. The Control4 / Drivers folder

should be located under "My Documents" on your PC.)

Launch Composer. If Composer is already running, shut it down

and restart it.

Using Composer, make a connection to Director. Select the System

Design Tab to add the Z2iR Driver. The Driver can be found by

selecting the Search Tab and then the Local Database. The device

type is "other" and the manufacturer is Card Access. NOTE: The

Driver can be added to any room in the project.

Power up the Z2iR Module using the supplied USB Power Supply

and Mini USB cable. In Composer, choose Connections and click

the Network Tab. Next click on the unidentified "Card Access

Z2iR" device. Identify the Z2iR in Composer by pressing the clear

identification button on the top of the Module four (4) times. The

LED should start flashing yellow. Once the Z2iR Module has been

identified in the system, the LED will blink green several times. If

identification fails, the LED will blink red several times.

• Once the Z2iR's MAC ID address appears in the Identify dialog

box, click "Close" to close the dialog.

• After a few seconds, the Z2iR Module's LED should change to a

solid GREEN color, indicating it has been successfully indentified in

the Control4 project.

Troubleshooting

If the Z2iR Module is not working it may need to be reset back to factory

settings. To perform a factory reset, do the following:

• While the Z2iR Module is still powered on, press the button on the

top cover 13 times.

• After the Z2iR Module has performed its reboot sequence, the LED

will turn solid red and it will need to be re-identified into the project.

NOTE: Any IR codes that were cached in the Z2iR Module will

be lost and will need to be re-transmitted and again cached

in the Module. In most instances, there may be a slight delay

(milliseconds) in operation the first time an IR code for the target

device is cached or re-cached.

Card Access Product Support

For help on the installation or operation of this product, email or call Card

Access Product Support. Please provide your exact model number and the

MAC ID/Serial Number for the device. You may contact Product Support by

phone (801-748-4900 x 1), by e-mail ([email protected]) or

on the Internet at http://www.cardaccess-inc.com/automation/support.

Regulatory Compliance

The Card Access Z2iR ZigBee-to-IR Module complies with relevant standards

established by the following regulatory bodies: Federal Communications

Commission (FCC), Conformité Européene (CE), Industry Canada, and

Restriction of Hazardous Substances (RoHS).

FCC

FCC ID: MHIZ2IR. This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Re-orient or relocate the Z2iR Module.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT! Changes or modifications not expressly approved

by Card Access, Inc. void the user's authority to operate the

equipment.

We, Card Access, Inc. of 11778 South Election Road, Suite 260, Salt Lake

City, Utah, 84020 USA, declare under our sole responsibility that the product,

the Card Access Z2iR Module, Model Number Z2IR10A-ZP, to which this

declaration relates, is in conformity with the following standards and / or other

normative documents:

EN60950, EN55022, EN55024

We hereby declare that the above named product is in conformity with the

essential requirements and other relevant provisions of Directive 1999/5/EC.

The conformity assessment procedure referred to in Article 10(3) and detailed

in Annex II of Directive 1999/5/EC has been followed.

Industry Canada

IC: 3681C-Z2IR10A

This class B digital apparatus complies with Canadian ICES-003.

CET appareil numerique de la classe B est conforme a la norme NMB-003 du

Canada'

This device complies with Industry

Le présent appareil est conforme aux

Canada license-exempt RSS

CNR d'Industrie Canada applicables

standard(s). Operation is subject to the

aux appareils radio exempts de licence.

following two conditions: (1) this device

L'exploitation est autorisée aux deux

may not cause interference, and (2) this

conditions suivantes: (1) l'appareil ne

device must accept any interference,

doit pas produire de brouillage, et (2)

including interference that may cause

l'utilisateur de l'appareil doit accepter tout

undesired operation of the device.

brouillage radioélectrique subi, même

si le brouillage est susceptible d'en

compromettre le fonctionnement.