AirStage ABYA045GTEH Installationshandbuch - Seite 14

Blättern Sie online oder laden Sie pdf Installationshandbuch für Klimagerät AirStage ABYA045GTEH herunter. AirStage ABYA045GTEH 16 Seiten.

Seite drucken

7.3. Function setting

• FUNCTION SETTING can be performed with the wired or wireless remote controller.

(The remote controller is optional equipment)

• Refer to the wired or wireless remote controller manual for detailed setting information.

• Refer to "7.1. Setting the address" for indoor unit address and refrigerant circuit address

settings.

• Turn the power of the indoor unit ON before starting the setting.

* Turning on the power to the indoor units initializes EEV, so make sure the piping air

tight test and vacuuming have been conducted before turning on the power.

* Also check again to make sure no wiring mistakes were made before turning on the

power.

Function details

Function

Setting number

number

00 Standard

Filter indica-

01 Longer

tor interval

02 Shorter

00 Enable

01 Disable

Filter indica-

Display only on

tor action

central remote

controller

(Forbidden)

00 Standard

Horizontal

01 Left half

swing airflow

direction

02 Right half

(Forbidden)

00 Standard

Cool air

01 Adjust (1)

temperature

trigger

02 Adjust (2)

00 Standard

01 Adjust (1)

Heat air

02 Adjust (2)

temperature

trigger

03 Adjust (3)

00 Enable

Auto restart

01 Disable

00 Super low

Follow the

Cool Air

setting on

Prevention

the remote

controller

00 Start/Stop

Emergency

stop

External

control

02 Forced stop

00 All

Error report

Display only on

target

central remote

controller

Follow the

Fan set-

setting on

ting when

the remote

cooling

controller

thermostat

OFF

01 Stop

Forced ther-

mostat off

Switching

function for

(Forbidden)

external

inputs

Refrigerant

leak detection

(Forbidden)

Single

setpoint auto

mode

Auto mode

type

(traditional)

Dual setpoint

auto mode

En-13

Default

Details

Adjust the filter cleaning interval noti-

fication. If the notification is too early,

change to setting 01. If the notifica-

tion is too late, change to setting 02.

Enable or disable the filter indicator.

Setting 02 is for use with a central

remote controller.

Adjust the horizontal swing airflow

direction.

(For horizontal swing equipped

models)

Adjust the cool air trigger tempera-

ture. To lower the trigger tem-

perature, use setting 01. To raise the

trigger temperature, use setting 02.

Adjust the heat air trigger tempera-

ture. To lower the trigger temperature

by 6 degrees C, use setting 01. To

lower the trigger temperature by 4

degrees C, use setting 02. To raise

the trigger temperature, use setting

03.

Enable or disable automatic system

restart after a power outage.

Restrain the cold airflow with making

the airflow lower when starting heat-

ing operation. To correspond to the

ventilation, set to 01.

Allow an external controller to start

or stop the system, or to perform an

emergency stop.

* If an emergency stop is performed

from an external controller, all re-

frigerant systems will be disabled.

* If forced stop is set, indoor unit

stops by the input to the external

input terminals, and Start/Stop by a

remote controller is restricted.

Change the target for reporting

errors. Errors can either be reported

in all locations, or only on the central

remote controller.

When set to 01, the fan stops when

the thermostat is OFF in cooling

operation. Connection of the wired

remote controller (2-wire type or

3-wire type) and switching its therm-

istor are necessary.

Setting is required when connecting

a refrigerant-leak detecting device.

(only for J-IIIL series)

Switch the setting method of

auto mode to single or dual

(cooling/heating).

For heat pump systems, it is

necessary to set the master indoor

unit (by wired remote controller).

Function

Setting number

number

00 0°C

01 0.5°C

02 1.0°C

03 1.5°C

Deadband

04 2.0°C

value

05 2.5°C

06 3.0°C

07 3.5°C

08 4.0°C

09 4.5°C

(Forbidden)

7.3.1. Button name and function

OPERATION indicator lamp (Green)

TIMER indicator lamp (Orange)

FILTER indicator lamp (Red)

7.3.2. Checking the function settings

Press and hold the "MANUAL AUTO" button on the indoor unit for 3 seconds to check

the function settings. It is necessary to disconnect the power in order to return to normal

operation mode.

(1) Indoor unit and refrigerant address indication

Indication pattern

Indicator name

OPERATION indicator lamp (Green)

TIMER indicator lamp (Orange)

FILTER indicator lamp (Red)

• Indoor unit address example

(Example) ADDRESS : 24

OPERATION

indicator

lamp (Green)

OFF

TIMER

indicator

0.5s 0.5s 0.5s 0.5s

lamp (Orange)

OFF

FILTER

0.5s 0.5s 0.5s 0.5s 0.5s 0.5s 0.5s 0.5s

indicator

OFF

lamp (Red)

• Indoor unit address example Refrigerant address example

(Example) ADDRESS : 30

OPERATION

indicator

1.0s

lamp (Green)

OFF

TIMER

indicator

0.5s 0.5s 0.5s 0.5s 0.5s 0.5s

lamp (Orange)

OFF

FILTER

indicator

OFF

lamp (Red)

Default

Details

Choose the minimum temperature

between cooling and heating

settings (deadband) for Dual

setpoint auto mode (set in No. 68).

MANUAL AUTO button

Indication pattern

Indoor unit

Refrigerant address

address

Flash (1.0s ON/1.0s OFF)

Address: tens place (0.5s ON/0.5s OFF)

Address: ones place (0.5s ON/0.5s OFF)

1 cycle 12 sec

10 sec

8 sec

1 cycle 12 sec

1.0s

9 sec

OFF