▶
To ensure correct installation, you must use a mater-
ial which is sufficiently stable and suitable for both
the structural conditions and the weight of the appli-
ance.
Changes to the electrical or mechanical assembly are
dangerous and may lead to malfunctions.
▶
Do not make any changes to the electrical or mech-
anical assembly.
The filter cover may swing out.
▶
Open the filter cover slowly.
▶
Take hold of the filter cover after opening until it no
longer swings out.
▶
Close the filter cover slowly.
Risk of injury when opening and closing the hinges.
▶
Keep your hands away from the hinges.
WARNING ‒ Risk of electric shock!
Sharp-edged components inside the appliance may
damage the connecting cable.
▶
Do not kink or trap the connecting cable.
If the appliance or the power cord is damaged, this is
dangerous.
▶
Never operate a damaged appliance.
▶
Never pull on the power cord to unplug the appli-
ance. Always unplug the appliance at the mains.
▶
If the appliance or the power cord is damaged, im-
mediately unplug the power cord or switch off the
fuse in the fuse box.
▶
Call Customer Service. → Page 8
▶
Repairs to the appliance should only be carried out
by trained specialist staff.
Improper repairs are dangerous.
▶
Repairs to the appliance should only be carried out
by trained specialist staff.
▶
Only use genuine spare parts when repairing the
appliance.
▶
If the power cord of this appliance is damaged, it
must be replaced by trained specialist staff.
Improper installation is dangerous.
▶
Connect and operate the appliance only in accord-
ance with the specifications on the rating plate.
▶
Connect the appliance to a power supply with al-
ternating current only via a properly installed socket
with earthing.
▶
The protective conductor system of the domestic
electrical installation must be properly installed.
▶
Never equip the appliance with an external switch-
ing device, e.g. a timer or remote control.
▶
When the appliance is installed, the mains plug of
the power cord must be freely accessible. If free ac-
cess is not possible, an all-pole isolating switch
must be installed in the permanent electrical installa-
tion according to the conditions of Overvoltage Cat-
egory III and according to the installation regula-
tions.
▶
When installing the appliance, check that the power
cable is not trapped or damaged.
13.6 Information on the installation situation
¡ Install this appliance on the kitchen wall.
13.7 Instructions for the exhaust air pipe
The appliance manufacturer does not provide any war-
ranty for faults attributable to the pipeline.
¡ Use a short, straight exhaust air pipe with as large a
pipe diameter as possible.
¡ Long, rough exhaust air pipes, many pipe bends or
small pipe diameters reduce the suction power and
increase the fan noise.
¡ An exhaust air pipe that is made of non-combustible
material.
¡ To prevent condensate from returning, fit the ex-
haust air pipe from the appliance with a 1° gradient.
Round pipes
Use round pipes with an inner diameter of 150 mm (re-
commended) or at least 120 mm.
Flat ducts
Use flat ducts with an inner cross-section that corres-
ponds to the diameter of the round pipes:
¡ Diameter of 150 mm corresponds to ap-
prox. 177 cm².
¡ Diameter of 120 mm corresponds to ap-
prox. 113 cm².
¡ Use sealing strips for different pipe diameters.
¡ Do not use any flat ducts with sharp bends.
13.8 General information
¡ To optimally detect the cooking vapours, install the
appliance in the middle of the hob.
¡ In order to freely access the appliance for servicing,
select an easy-to-reach installation site.
¡ The surfaces of the appliance are sensitive. Avoid
damaging them during installation.
13.9 Installation
Preparing the appliance
▶
Remove the grease filters.
To avoid causing damage, do not bend the grease
filters.
Checking the wall
1.
Check whether the wall is horizontal and adequately
load-bearing.
The max. weight of the appliance is 25 kg.
2.
Drill the hole depth in accordance with the length of
the screws.
3.
Install the appliance with a fixing material which is
sufficiently stable and has been adjusted accord-
ingly for both the structural conditions and the
weight of the appliance.
4.
Check the cut-out area for existing cables of other
appliances.
Preparing the wall
1.
Cover the hob to prevent damage.
2.
Remove the drilling template.
The cardboard drilling template is part of the pack-
aging.
3.
Mark a vertical centre line on the wall from the ceil-
ing to the lower edge of the appliance.
4.
Using the drilling template, measure and mark the
positions of the fastening screws.
Installation instructions en
11
Seite drucken