Draper Salara Einbauanleitung

Blättern Sie online oder laden Sie pdf Einbauanleitung für Projektionsfläche Draper Salara herunter. Draper Salara 2 Seiten. 220v ir plug & play
Auch für Draper Salara: Kurzanleitung (2 seiten), Einbauanleitung (2 seiten), Einbauanleitung (2 seiten)

Seite drucken



Read instructions through completely before proceeding.



Follow instructions carefully. Installation contrary to instructions invali-

dates warranty.



Screen should be accessible for complete removal should fabric

become damaged or should other service be required.



Screen should be installed level (using a carpenter's level).



Nothing should be fastened to screen dowel or viewing surface.



Operating switch(es) packed separately in screen carton. Do not

discard with packing material.

 Screen operates on 110-120V, 60 Hz. AC, 1.1 amp current draw.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

These instructions are meant as a guide only. They do not imply any

responsibility on the part of Draper, Inc. for improper installation or faulty

workmanship at the jobsite.

Wall/Ceiling Flush Mounting

 Attach Mounting Brackets to wall or ceiling (see Fig. 1). The installer should

furnish screws, toggle bolts, molly bolts, nylon or lead anchors as required

by the mounting surface. Installer also needs to ensure the mounting

surface is reinforced sufficiently to support the screen. Brackets must be

level with each other.

Mounting

Bracket

Wall

(3.5 cm)

 Plug the power cord (included if ordered) into the motor end of the screen

case (left end as the viewer sees the screen).

 Attach the screen by snapping the extrusions on the back of the case onto

the brackets. With the lower edge of the screen case tilted away from the

wall, engage the rib on top of the case with the slot on each bracket. Slide

the screen case along the brackets to adjust the screen location from left to

right if necessary (see Fig. 2). Once the case is in position, pivot the case

back toward the brackets until the lower edge of the case "snaps" into place

with the spring-loaded latch (see Fig. 3).

Extrusions along

back of case

Installation Instructions

IR Plug & Play Salara by Draper

Caution

Ceiling

Mounting

Bracket

(3.8 cm)

Figure 1

Figure 2

Printed in U.S.A.

Electrical Connections

Screen operates on 110-120V 60 hz. AC, 1.1 amp current draw. Duty cycle:

On 26 seconds/Off 3 minutes. Screen shipped with internal wiring complete.

Junction box is located inside left endcap and cover plate is secured to

endcap with one screw. Screen is shipped with control switch(es) fully boxed.

No external wiring is needed. unless connecting to RS232. Plug cord into

standard 110-120V AC outlet.

All operating switches should be "OFF" before power is connected.

Please Note: If you remove the plug and hardwire this unit, do not wire in

parallel with other motors.

Screen is equipped with a handheld remote or 3-position operating switch

(see below). Three positions (up-off-down) permit operation to be stopped at

any point. Factory adjusted limit switches automatically stop screen when fully

down or fully up.

Wiring/Control Options:

Plug & Play

—

Provided with built-in IR receiver, handheld IR remote

control transmitter and 10' (3m) IEC cordset. No wiring necessary except to

connect to RS232.

Please Note: Screen limits are factory set for optimum performance of

the screen. A procedure is outlined below for minor tweaks, but any

adjustment of these limits may negatively affect the flatness of the

screen surface and could also void the warranty. Please check with

Draper prior to resetting screen limits.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

CAUTION: Be sure all switches are in "off" position before adjusting

limit switches.

There are two holes in the left end cap (as seen from audience) for both limit

switch adjustments and neither is labled. The hole closest to the audience is

the up limit and the hole furthest from the audience is the down limit

"Down" limit switch: Down stopping position can be adjusted by turning

knob furthest from audience with a screw driver or hex wrench. Turning knob

counterclockwise will allow viewing surface to run farther down. Turning it

clockwise will reduce the amount of exposed viewing surface.

"Up" limit switch: You should never have to adjust this limit! If you do,

however, the Up stopping position can be adjusted by turning knob closest

to audience with a screw driver or hex wrench through the small grommet.

Turning knob counterclockwise will allow surface to run farther into the screen

case. Turning it clockwise will allow viewing surface to stop farther out of the

screen case.

If you encounter any difficulty installing or servicing your Salara, call your dealer

or Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.

Figure 3

Operation

Adjustments

Dimensional drawings on page 2

US Patent

Pending.