Draper Targa Installations- und Betriebsanleitung

Blättern Sie online oder laden Sie pdf Installations- und Betriebsanleitung für Projektionsfläche Draper Targa herunter. Draper Targa 3 Seiten. Electrically operated projection screen with motor-in-roller
Auch für Draper Targa: Installations- und Betriebsanleitung (4 seiten), Installations- und Betriebsanleitung (2 seiten), Installations- und Betriebsanleitung (2 seiten), Installations- und Betriebsanleitung (2 seiten), Installations- und Betriebsanleitung (4 seiten), Installations- und Betriebsanleitung (2 seiten), Installations- und Betriebsanleitung (4 seiten), Installations- und Betriebsanleitung (2 seiten), Installations- und Betriebsanleitung (2 seiten), Anleitung Handbuch (8 seiten)

Seite drucken

Draper Targa Installations- und Betriebsanleitung

➀ Read instructions through completely before proceeding.

➁ Follow instructions carefully. Installation con trary to instructions in val i dates

warranty.

➂ Screen should be accessible for complete removal should fabric be come

damaged or should other ser vice be required.

➃ Screen should be installed level (using a carpenter's level).

➄ Nothing should be fastened to screen dowel or viewing surface.

➅ Operating switch(es) packed separately in screen carton. Do not dis card

with packing material.

➆ Screen operates on 110-120V, 60 hz., 1.1 amp current draw.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

These instructions are meant as a guide only. They do not imply any

re spon si bil i ty on the part of Draper, Inc. for improper in stal la tion or faulty

work man ship at the jobsite.

Hanging Screen

General:

When locating view ing surface and checking clear ance for screen's op er a tion, re-

member surface is centered in case. Handle case care ful ly to protect its ﬁ nish.

Regardless of mounting method, screen should be positively and securely sup-

port ed so that vibration or even abusive pulling on the viewing surface will not

cause case to work loose or fall. Installer must insure that fas ten ers used are of

adequate strength and suit able for the mounting sur face cho sen.

Suspended Installation:

Suspend screens from holes in endcaps as shown. "S" hooks, chains (or cable)

and turn buck les should be provided by installer. "S" hooks should go through

the front holes on the endcaps (see drawing on page 2), and both ends of the

"S" hooks should be crimped for additional safety. Chains should be attached to

beams or other struc tur al mem bers. Turn buck les should be adjusted so screen

hangs level.

Wall Installation:

Mount screen through holes in back of endcaps as shown. Installer should

furnish screws, toggle bolts, molly bolts, nylon or lead anchors as required.

Wall Installation with 6" Extension Brackets:

Mount the brackets (not in clud ed with screen—see diagram on page 2) using

hard ware rec om mend ed for "Wall Installation" (above). Then, sus pend the

screen from the front holes with "S" hooks (as in "Suspended"). For added

safe ty, be sure to crimp both ends of the "S" hooks so the screen can not

come off. For a more rigid in stal la tion, mount the screen from the back holes

to the front of the bracket by us ing the screws and nuts pro vid ed with the

brack ets.

Recessed Installation:

Recess should permit access for removal of screen if necessary. Screen may

be mounted as in suspended or wall installation. Optional Ceiling Opening

Trim Kit available; see diagrams below and on page 2, and separate instruction

sheet (included with Ceiling Opening Trim Kit).

Electrical Connections

Screen operates on 110-120V, 60 hz., 1.1 amp current draw. Duty cycle: On 28

seconds/Off 4 minutes.

Junction box is located inside left endcap and cover plate is secured to endcap

with two screws. Junction box contains red, black and white pigtail leads and

green internal ground wire, per wiring di a gram on reverse.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire connecting screen to switch(es) and switch(es) to power sup-

ply should be furnished by installer. Please Note: Screen must be installed in

accordance with the requirements of the Local Building Codes, the Canadian

Electrical Code (CEC), CAN/CSA C22.1 and the National Electric Code (NEC),

NFPA 70. An appropriate disconnect device shall be provided as part of the

building installation. Please Note: Do NOT wire motors in parallel.

Form Targa_Inst10

Installation/Operating Instructions

Targa Electric Projection Screen by Draper

Caution

Printed in U.S.A.

All operating switches should be "off" before power is connected.

Plug-in power cord option available with built-in low voltage motor.

For Reconﬁ guration/Conversion of Non-detachable Power Cord to

Field Wiring for Models TAR-28, TAR-29 and TAR-30 Only:

① Disconnect cord plug from outlet.

② Remove junction box cover.

③ Disconnect wire nuts from black, white and green wires.

④ Remove power cord and strain relief from screen.

⑤ Connect the black motor wire to "hot" supply wire.

⑥ Connect white motor wire to "neutral" supply wire.

⑦ Connect green/yellow wire to "ground" supply wire.

⑧ Replace junction box cover.

Screen Case

Before operating screen remove tape securing fabric and dowel to roller. If view-

ing surface hangs out of case 8"-9", tape has prob a bly been bro ken by rough han-

dling in ship ment, allowing surface to "un wrap" one turn about the roller. Manually

wrap fabric back around the roller without turning the roller itself.

110-120V Single Station Control — 3-position up-off-down switch per mits op er a-

tion to be stopped at any point. Factory adjusted limit switch es au to mat i cal ly stop

screen when fully down or fully up.

110-120V Multiple Station Control—Switches are similar in ap pear ance to

110-120V Single Station Control. Screen stops when switch is re leased and may

be re start ed in either direction. Factory adjusted limit switch es stop screen auto-

matically when fully up or fully down.

24V Control — Three-button up-stop-down switch es stop at any point de sired,

operate in any sequence. Factory adjusted limit switches au to mat i cal ly stop

screen when fully up or fully down.

Key Operated Switching — Two kinds of key-operated switches are op tion al ly

available with this unit. ➀ The key-operated power sup ply switch controls power to

the screen and switches. When it is "off", the switch es will not operate screen. Key

may be re moved from the switch in either "on" or "off" position. ➁ A three-po si tion

key switch per mits the screen to be operated directly by key. In this case, the

screen's operator must always have a key.

RS232/Ethernet—Serial communication and network communication optionally

available with wall switches, RF or IR remote.

Plug & Play

—Provided with handheld IR remote control transmitter and

10' (3m) cord. No wiring necessary except to connect to RS232. Screen is

equipped with a handheld remote or 3-position operating switch (see below).

Three positions (up-off-down) per mit operation to be stopped at any point.

Factory adjusted limit switches au to mat i cal ly stop screen when fully down or

fully up.

Limit Adjustments (Standard/Quiet Motors)

(Height adjustments are made at the motor using white/yellow screws)

Tools needed: Flashlight, small ﬂ athead screwdriver/Allen wrench (4mm or

").

Screen settings have been factory set as ordered and should not normally

require further adjustment. However, if you ﬁ nd it necessary to adjust for more

or less viewing area, proceed as follows.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down. When running up, the

dowel should never wrap over the roller. When run to the down limit, a

minimum of 1¼ wraps of fabric must remain on the roller.

The motor limit screws are normally located on the audience left of screen

roller, and the viewing surface rolls off the back of the roller. If the viewing

surface is coming off the front of the roller (motor on left), or the motor is on the

audience right of the screen roller (with viewing surface rolling off the back),

reverse the following instructions.

If you encounter any difﬁ culties installing or ser vic ing your Targa screen, call your

dealer or Draper Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.

Back

Ceiling Tile

(By others)

Operation