Draper Dual Roller FlexShade with Pocket Headbox Einbauanleitung
Blättern Sie online oder laden Sie pdf Einbauanleitung für Inneneinrichtung Draper Dual Roller FlexShade with Pocket Headbox herunter. Draper Dual Roller FlexShade with Pocket Headbox 4 Seiten.
Auch für Draper Dual Roller FlexShade with Pocket Headbox: Einbauanleitung (4 seiten)
Seite drucken
Dual Roller FlexShade with Pocket Headbox
Installation Instructions
The Dual Roller FlexShade with Pocket Headbox is shipped in one carton;
(1)
the shades and/or screen are shipped in a separate carton; controls may also be
shipped in a separate carton.
Verify dimensions of opening and refer to order for overall dimensions of the unit.
(2)
Dimensions are noted on the outside of the carton. Shade dimensions are given
width x height.
(3)
If installing bead chain clutch shades, they are to be installed in areas accessible
to young children, be certain to use cord tension device and heed warning at right.
(4)
Installer must ensure Dual Roller FlexShade is positively and
securely anchored with appropriate fasteners for mounting surface.
(5)
Hanger brackets are shipped separately.
For motorized units, make sure POWER IS OFF before making electrical
(6)
connections. Use extreme caution when working with electric motors.
(7)
Do not wire motors in parallel without written permission from Draper.
Please read the following installation guidelines thoroughly and follow them
(8)
carefully. Failure to do so may cause product to fall or otherwise fail, and
invalidates warranty.
Please Note: Custom products/installations may not be reflected by this document.
Call Draper, Inc. if you have questions about your installation.
Pocket Headbox Installation
You must provide adequate clearance for removal of the Roller Assembly
during installation and maintenance.
The Pocket Headbox for the Dual Roller FlexShade must be mounted
directly to the ceiling, or to a continuous blocking that has been secured to the
building structure (see Fig. 2 at right).
(1)
Lift the headbox into mounting position. Mark the location of the optional
pre-drilled pocket mounting holes and the Endcap mounting holes on the top
side of the headbox (Fig. 1) on the ceiling or continuous blocking.
Drill small starter hole (if necessary) in mounting surface.
(2)
1
/
1
8
Endcap
Mounting
Holes
Optional
Vent Holes
Pocket
Pocket
Mounting
Mounting
Holes
Holes
Copyright © 2017 Draper Inc.
Form DualRollerFlexShade_PHB_Inst17
Caution
"
(3)
Mount pocket headbox
using appropriate fasteners
3"
for surface.
NOTE:
The installer is responsible for
selecting appropriate mounting
hardware for site conditions.
(4)
Mount endcaps using
appropriate fasteners for
surface.
NOTE:
It is essential that endcaps
are fastened securely to
Figure (1)
the mounting surface and
are not able to move from
side to side.
Printed in U.S.A.
1
/
"
1
8
WALL
Wall Clip
(pre-attached to headbox)
Window
Installing Closure Panel
B
Closure Panel
Headbox
Figure (3)
C
Headbox
Closure Panel
If you encounter any difficulties installing or servicing your Dual Roller FlexShade,
call your dealer or Draper, Inc., Spiceland, Ind., (765) 987-7999 or fax (765) 987-7142.
3"
Endcaps Mounted
to Continuous
Blocking (by others)
Secured to
Building Structure
Continuous
Blocking
(by others)
3"
Closure
Ceiling
Panel
(by others)
Figure (2)
B
Closure Panel
Headbox
C
Headbox
Closure Panel