Draper FlexLouver 75E Einbauanleitung - Seite 2
Blättern Sie online oder laden Sie pdf Einbauanleitung für Inneneinrichtung Draper FlexLouver 75E herunter. Draper FlexLouver 75E 4 Seiten. Rack arm systems
Seite druckenFlexLouver™ Rack Arm Systems by Draper
Louver Attachment
50A
Please Note: Install one Louver to ensure that all of the Rack Arms are held in
the same position when the Drive Shaft is installed. After Drive Shaft installa-
tion is complete, finish attaching the remainder of the Louvers.
1 Grasp Louver with both hands. Depending on length of Louver, this may
require more than one person.
2 Carefully squeeze Louver to increase the arc.
3 Place Louver in Rack Arm attachment points and release pressure to allow
it to expand back into shape, and into place on the Rack Arm.
4 Carefully slide back and forth, if necessary, to correct position.
5 Repeat at all Slat Clip positions. Please Note: This assumes that there
are only two rack arms. Often there will be more. This is applicable to
all of the louver options.
80R
Please Note: Install one Louver to ensure that all of the Rack Arms are held in
the same position when the Drive Shaft is installed. After Drive Shaft installa-
tion is complete, finish attaching the remainder of the Louvers.
1 Carefully grasp Louver with both hands. Depending on length of Louver,
this may require more than one person. It is important not to allow the
Louver to flex along its length; once a roller edge Louver has been dam-
aged, it cannot be repaired and must be replaced.
2 Insert one side of the Slat clip into the rolled edge of the Louver.
3 Rotate the Slat Clip far enough to allow the other side of the Slat Clip to go
into the rolled edge on the other side of the Louver.
4 The Slat Clip is then rotated back until it is perpendicular to the edges of
the slat.
5 For exterior installations, install Slat Retaining Spring.
Standard number
of Rack Arms (80R)
35" = 2 pieces
36" - 70" = 3 pieces
71" - 105" = 4 pieces
106" - 140" = 5 pieces
141" - 175" = 6 pieces
Side View
Retainer
Clip
Side View
www.draperinc.com
Please Note: Install one Louver to ensure that all of the Rack Arms are held in
the same position when the Drive Shaft is installed. After Drive Shaft installa-
tion is complete, finish attaching the remainder of the Louvers.
75E/88E
1 Grasp Louver with both hands. Depending on length of Louver, this may
require more than one person.
2 Place Louver's extrusion "foot" into Rack Arm groove.
3 Snap the other Louver extrusion into place on the other edge of the Rack
Arm.
4 Carefully slide back and forth, if necessary, to correct position.
5 Repeat with other end of Louver.
6 For exterior installations, tighten screw to lock the Louver onto the Slat Clip.
Cleaning and Maintenance
Under normal circumstances, the FlexLouver Rack Arm System requires
no special maintenance or adjustments other than occasional cleaning by the
end user.
For general cleaning, use a sponge and water with a mild detergent to
wipe down the louvers when in a closed position. Following cleaning, move
the louvers to the open position to allow them to dry.
Do not use acidic or abrasive cleaning agents as they could damage
the surface of the louvers.
Caution: Do not operate when snow and/or ice may be present on the
system. Operating in snow and ice conditions will cause damage to the
system.
(765) 987-7999
Page 2 of 4
75E
Side View
88E
Side View