Draper LightBloc Zip Installationsanleitung Handbuch - Seite 3

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Inneneinrichtung Draper LightBloc Zip herunter. Draper LightBloc Zip 6 Seiten.
Auch für Draper LightBloc Zip: Installationsanleitung Handbuch (6 seiten)

Seite drucken

LightBloc

Mounting Headbox - Zip 127 Angled Headbox

The LightBloc Zip 127 Angled Headbox can be mounted permanently to the

wall or ceiling (See Mounting Headbox - Permanently to Ceiling or Wall on

page 1); or the Headbox can rest atop the Side Channels and is held in place

there by two mounting studs coming down from the endcaps.

PLEASE NOTE:

Steps 1-5 of the Mounting Side Channels

section must be completed before mounting

the Zip 127 Angled Headbox. It is critical that

the full length of each Side Channel

is secured to the mounting surface.

1 Remove screws from bottom of Headbox,

remove Fascia and set aside. (See Fig. 11).

HEADBOX

MOUNTING

STUD

S i

d e

C h

a n

n e

3 Insert "Zippers" on the side of the Hem Bar into the fabric retainers in the

Side Channels (See Fig. 12).

4 Insert Headbox mounting stud into Side Channel (See Fig. 12).

5 Return Fabric Retainers to Side Channels and re-attach Covers.

The LightBloc Zip can also be installed in a pocket in the ceiling. You must

provide adequate clearance for removal of the Roller Assembly during

installation and maintenance.

The minimum depth of the ceiling pocket for the LightBloc Zip 92 is 4¾"

(120mm), and for the LightBloc Zip 127 is 6¼" (158mm). See Fig 13 below.

FlexShade Zip 92

4 ¾"

(120mm)

(92mm)

7¼"

(

183mm)

Figure (11)

Zip by Draper

™

2 Insert "Zipper" on one side of

the Hem Bar into the fabric

retainer in the Side Channels

(See Fig. 12).

HEADBOX

MOUNTING

STUD

S i

d e

C h

a n

n e

Figure (12)

Pocket Installation

FlexShade Zip 127

6¼" (

5" (

(92mm)

(148mm)

If the system is installed in a recess, it is unlikely that there will be sufficient

space above the side channels to allow the Headbox to be mounted onto them.

In these instances follow the steps for preparing the system (See Mount-

ing Headbox - Zip 127 Angled Headbox). Then mount the Headbox onto

the side channels and present the entire system into the opening. Hold the

Figure (11)

system in position and use appropriate screws to fix the side channels in

place. Apart from this, the other steps should be followed as described.

The LightBloc Zip operates on 110-120V, 60 Hz. current. Shade is shipped

with internal wiring complete and control switch (es) fully boxed, and supplied

with a 6' cable lead (standard). Longer lead can be substituted by removing

REMOVE

two screws in motor end of roller, removing lead, plugging new lead in, and

FASCIA

replacing screws. Wire to connect shade to switch (es) and switch (es) to

power supply should be furnished by installer. Connections should be made

in accordance with attached wiring diagram, and wiring should comply with

national and local electrical codes.

DO NOT wire motors in parallel without written permission from Draper.

All operating switches should be "off" before power is connected.

ZIPPER

CAUTION: Be sure all switches are in "off" position before adjusting limit switches.

Always be prepared to shut off manually when new adjustment is being tested.

Do not allow the shade roller to become exposed by running the shade

fabric too far down. Shade may be severely damaged if allowed to run too far up

or down. Each shade's limit switch must be set if using group control system.

HEMBAR

1 Fully depress both limit switch push buttons, then operate wall switch to make

sure system works properly.

2 Raise shade to desired "up" stop position.

3 Set upper limit by depressing and releasing the proper (back) push button.

FABRIC

4 Lower shade to desired "down" stop position.

RETAINER

5 Set lower limit by depressing and releasing the proper (front) push button.

STRIP

For instructions on setting limits on these motors, consult Draper's Motorized

Shade Handbook, available in the motorized shades section of www.draperinc.com.

1 Connect the ILT switch to the motor via the terminal blocks, or via the modular

port using four conductor modular cable. When using modular cable, the cable

connectors MUST NOT be crimped in

reverse, as with standard telephone cable.

2 Set the slide switch to the lower

position. Press and hold the DOWN

button on the switch to move the

viewing surface to the desired lower

limit. If the shade moves in the opposite

direction, release the DOWN button

and press and hold down the STOP

button for four seconds. This will

reverse the operation of the

UP and DOWN switches.

3 Move slider switch into center position.

Wait a couple of seconds.

158mm)

Please Note: If you move the slider switch

from down to up in one motion it sets the two

127mm)

limits in the same position.

4 Set the slide switch to the higher

position. Move the shade to the desired

(

127mm)

upper limit by pressing and holding the

UP button on the wall switch.

7¼"

(

183mm)

5 Return the slide switch to the center

position to return to normal operation.

6 To set the shade to an intermediate

position, move the shade to the desired

position and press the STOP button. Press and hold the STOP button for at

least three seconds to record the postion.

Please Note: Pressing and releasing the UP button on the switch will move the shade to its

Figure

upper limit. Pressing and releasing the DOWN button will move the shade to its lower limit.

While the motor is in motion, pressing the STOP button for less than two seconds will stop the

shade at its present position. Once the motor is stopped, pressing the STOP button will move

the shade to its intermediate position.

Pressing and holding the STOP button, when the motor is at rest or in motion, for at least

three seconds will record a new position.

www.draperinc.com

(765) 987-7999

Alternate Mounting for Jamb Recessed

Installations (Zip 127 Angled Only)

Complete Electrical Connection

Limit Switch Adjustments—Standard Motor

Limit Switch Adjustments—RTS Motors

Limit Adjustments (ILT Motors)

FlexShade Zip 92

4 ¾"

(120mm)

(92mm)

(148mm)

Page 3 of 6

POSITION

FUNCTION

POSITION

FUNCTION

Set LOWER limit

DOWN

Set LOWER limit

DOWN

Set UPPER limit

Normal Operation

CENTER

Normal Operation

CENTER

Back View of Wall Switch

To Motor

with

Built-In

Low Voltage

Slide

Switch

Slide

Switch

To Motor

with

Built-In

Low Voltage

To Motor

with

Built-In

Low Voltage

Please Note: 5V DC must be

connected to be able to set

limits using the wall switch.