Draw tite 118798 Einbauanleitung

Blättern Sie online oder laden Sie pdf Einbauanleitung für Automobilelektronik Draw tite 118798 herunter. Draw tite 118798 3 Seiten. T-connector

Seite drucken

Installation Instructions

Directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

Toyota Avalon

WARNING

ALWAYS read and follow all warnings and

instructions included with purchase before

beginning installation. Keep for future reference.

DO NOT exceed lower of towing manufacturing

rating (including in your vehicle owner's manual)

or specific amperage ratings stated on product.

ALWAYS read, understand and follow all

warnings and instructions printed on tow

vehicle's battery.

ALWAYS wear safety glasses and use all safety

precautions during installation.

118798-037

Rev. A

ENGLISH

TOOLS REQUIRED:

Trim Panel Remover, 10mm Socket & Ratchet

or 10mm Wrench, Drill (3/32" Drill Bit), 1/4"

socket, Wire Crimpers, Wire Cutters, Philips Head

Screwdriver, Test-probe

1. Open trunk. Temporarily remove the rear threshold

plate. Partially remove the felt trunk liner behind the

A b c

taillights.

2. On the driver and passenger sides of the vehicle,

locate the vehicle's taillight wiring harness. The

taillight wiring harness will have a connection point,

on both sides, matching the ends of the T-One

Connector. Separate this connector, being careful

not to break the locking tabs. All connector surfaces

should be clean and free of dirt.

3. On the driver's side, insert the T-One

end, with the yellow wire, between the vehicle

wiring connectors and lock into place. Be careful

not to damage the locking tabs and be sure that

connectors are fully inserted with locking tabs in

place.

4. Route the T-One

Connector end with green wire to

the passenger's side behind the panels and along

the threshold. Plug the T-Connector end with the

green wire in-between the mating plugs on the

passenger's side taillight socket and vehicle wiring

harness.

5. On the driver's side, locate existing ground stud.

Loosen bolt, place screw eyelet on stud and

re-tighten bolt.

WARNING

Make sure all other ground connections are secure

when removing and reattaching the ground stud.

11/16/2018

On the driver's side, locate the black 12 ga. Power

wire from the T-Connector box. Attach the black 12

ga. wire provided. Route the black wire along the

exterior frame or follow the existing wiring along

the thresholds into the engine compartment up to

the battery avoiding areas that may pinch or break

the wire.

WARNING

If routing the wire thru a grommet and along the

exterior of the vehicle, be careful to avoid any hot

pipes, heat shields, the fuel tank or any other points

that may pinch or break the wire.

7. Disconnect the vehicle's Negative (-) battery cable.

If not removed, remove the fuse from the yellow

fuse holder (provided). After cutting the fuse holder

wire, attach the ring terminal and secure to the

vehicle's Positive (+) battery cable. Connect the

Connector

other end of the fuse holder to the black 12 ga.

wire, using the yellow butt connector (provided).

WARNING

Read and follow all warnings and cautions printed

on the tow vehicle's battery.

8. Reconnect the vehicle's Negative (-) battery cable

and install the 15 amp fuse into the fuse holder

from step 7.

WARNING

All connections must be complete for the T-One

Connector to function properly. Test and verify

installation with a test light or trailer once installed.

For initial test, reset vehicle electrical system by

temporarily removing the key from the ignition.

g h

9. Locate a flat surface in an out of the way place and

mount the T-One

Connector's black box-module,

to prevent damage or rattling.

10. Secure the remainder of the T-One

harness with the cable ties provided, to prevent

damage or rattling and being careful to avoid any

areas that would pinch, cut or melt the wire.

11. Replace carpet, and any other clips or panels that

were removed during installation being careful not

to cut or pinch the wires.

NOTE

Store 4-Flat in trunk area when not in use.

WARNING

Overloading circuits can cause fires. DO NOT

exceed stated product ratings. Read vehicle's

owner's manual & instruction sheet for additional

information.

T-Connector