Alemlube 9323629006149 Technisches Handbuch für den Eigentümer - Seite 6

Blättern Sie online oder laden Sie pdf Technisches Handbuch für den Eigentümer für Werkzeuge Alemlube 9323629006149 herunter. Alemlube 9323629006149 8 Seiten. 20v lithium-ion cordless grease gun 450g

Seite drucken

OWNER'S TECHNICAL MANUAL

20V Lithium-ion Cordless Grease Gun 450g

FILLING WITH A PUMP

WARNING: The gun can be equipped with a low pressure filling valve (3). Never mount a high pressure lubrication

fitting, serious damage can occur due to high pressure. Use only low pressure couplings.

1. Insert the rod completely into the tube.

2. Fasten the filling coupler on the gun filling valve (3).

3. Slowly start the filling pump and watch the rod move.

4. When the filling rod is fully extended, approximately 20cm (8 inch), stop the pump immediately. Never overfill!

5. Disconnect the charging coupler.

6. Use the bleed valve to release any trapped air. See "Grease gun priming".

7. Set the display meter to zero.

GREASE PRIMING

WARNING: Air pockets trapped in the grease can cause a lack or loss of priming in the gun. Always remove air after

refilling the grease tube or when the gun loses priming and does not pump grease.

1. Make sure the rod is not locked.

2. Insert the rod into the tube.

3. Loosen the screw on the bleed valve without removing it completely.

4. Pull the trigger for 10-20 seconds.

5. If no grease comes out of the hose end, repeat from step 3.

OPERATION

DISPLAY AND WORKING LIGHT

Pressing the gun trigger automatically activates the display and the working LED light. To save energy, both are automatically

switched off after 20 seconds.

The LED light can be turned on and off independently by pressing button "A" (16).

The display shows the grease level in the cartridge, the amount of grease dispensed, the mode of operation, the units

of measurement and the battery charge level.

GREASE FILLING

SPEED SELECTION

The gun is equipped with 2 operating modes, a LOW mode in which a maximum flow

rate of 100g/min is obtained and a HIGH mode in which flow rates of up to 160g/min

are achieved (depending on the back pressure and the type of grease and temperature).

In both modes the maximum working pressures of the gun can be reached, obtaining

a longer battery life in the LOW mode.

To switch between the two operating modes, press button B, the display will alternately

show "H" (HIGH mode active) or "L" (LOW mode active).

GREASE MEASUREMENT (ESTIMATION)

When you are supplying grease, the display will show the amount of grease dispensed

in grams or ounces. To change units, press and hold button A for 5" to toggle between

the two units.

An estimate of the grease level in the tube is shown graphically on the screen (15d).

Pressing button "B" for 8" resets the counter to zero and restores the full graphic

grease level indicator (15d).

BATTERY CHARGE LEVEL

The display shows 4 states of the battery charge level (15a) in graphic form. When none of the bars are visible, recharge

the battery according to the recommended instructions.

STALL ALARM

A red light on the display indicates a blocked lube point or another issue. If a red light on the display occurs, please contact

your local Alemlube branch for further information.

NSW/ACT

QLD/PNG

TEL: (02) 9677 1555

TEL: (07) 3204 9166

FAX: (02) 9675 1155

FAX: (07) 3204 1224

VIC/TAS

TEL: (03) 8787 8288

FAX: (03) 8787 8266

Visit our website at

www.alemlube.com.au

SA/NT

TEL: (08) 9302 4199

TEL: (08) 8241 7111

FAX: (08) 9303 2095

FAX: (08) 8241 7011

www.alemlube.co.nz

630A

TEL: (09) 447 1007

FAX: (09) 447 1008