Bosch FAP-OC 500Series Service-Handbuch - Seite 19

Blättern Sie online oder laden Sie pdf Service-Handbuch für Backofen Bosch FAP-OC 500Series herunter. Bosch FAP-OC 500Series 41 Seiten. Built-in wall ovens
Auch für Bosch FAP-OC 500Series: Installationsanleitung Handbuch (21 seiten), Gebrauchsanweisung Handbuch (40 seiten), Installationshandbuch (6 seiten), Informationen zum Produkt (40 seiten), Installationshandbuch (28 seiten), Benutzerhandbuch (48 seiten), Benutzerhandbuch (48 seiten), Installationshandbuch (28 seiten), Handbuch für Gebrauch und Pflege (44 seiten), Installationshandbuch (32 seiten), Gebrauchs- und Pflegeanleitung / Installationsanleitung (40 seiten), Kurzreferenz-Handbuch (4 seiten), Handbuch für Gebrauch und Pflege (27 seiten), Installationshandbuch (24 seiten), Installationshandbuch (32 seiten), Handbuch für Gebrauch und Pflege (24 seiten), Installationshandbuch (28 seiten), Handbuch für Gebrauch und Pflege (21 seiten), Installationshandbuch (32 seiten), Service-Handbuch (36 seiten), Installationshandbuch (32 seiten), Schnellstart- und Sicherheitshandbuch (13 seiten)

Seite drucken
Bosch FAP-OC 500Series Service-Handbuch
58300000202181 ARA EN B

6.4.1 Replacing the Front Panel Assembly

1. Remove power to the oven.
2. Protect the top of the oven door to prevent damage to the
stainless front panel or door.
3. Remove two screws on the underside of the panel assembly –
one on the right and one on the left – which secure the panel
to the vent trim; it is not necessary to remove the center screw
at this time.
NOTICE
Use care when detaching the front panel. There is very little slack in
the wires connecting the control module to the display board and the
control module to the LH switch, so it may not be possible to fully
rotate the front panel 90°.
4. Swing the bottom of the control panel slightly outward, then lift
to disengage the side flanges of the front panel carrier from
the slots in the side trim.
Figure 22 Detaching the control panel from the side trims
5. Disconnect the ground wire and the communication harness
connectors at the display board and touch pad; set the front
panel on a flat work surface.
6. Remove the knobs.
Copyright by BSH Home Appliances Corporation
This material is intended f or the sole use of BSH authorized persons and may contain conf idential and proprietary inf ormation. Any unauthorized rev iew, use, copy ing, disclosure, or distribution in any f ormat is prohibited.
Novemb er 2018
Figure 23 Separating the carrier from the front panel assembly
Figure 24 Front panel service assembly includes stainless skin, touch pad, TCM

6.4.2 Replacing the Display Module

1901 Main St ▪ Suite 600 ▪ Irvine, CA 92614
Service Manual for Bosch 500 Series Built-in Wall Ovens
7. Remove the screw in the bottom center of the panel, which
secures the panel to the carrier directly behind it.
8. Separate the carrier from the front panel assembly.
9. Reassemble the control panel using the new front panel
service assembly.
10. Reattach the control panel, restore power, and test operation.
The display module is secured to the control panel carrier with
four nylon spacers (standoffs).
Figure 25 Display board secured to carrier with 4 nylon spacers
Page 19 of 41
800 944-2904