Bosch 0 601 530 1 Original-Bedienungsanleitung - Seite 5

Blättern Sie online oder laden Sie pdf Original-Bedienungsanleitung für Elektrowerkzeug Bosch 0 601 530 1 herunter. Bosch 0 601 530 1 38 Seiten.

Seite drucken

OBJ_BUCH-519-002.book Page 5 Wednesday, October 19, 2016 9:56 AM

Safety Warnings for Nibblers

 The power tool is not suitable for stationary operation.

For example, it may not be clamped in a vice or fastened on

a workbench.

 Wear protective gloves while working and pay particu-

lar attention to the mains cable. Sharp burrs develop at

the cut steel sheet and can cause injuries to the operator or

damage the mains cable.

 Secure the workpiece. A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.

 Products sold in GB only: Your product is fitted with a

BS 1363/A approved electric plug with internal fuse

(ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should

be cut off and an appropriate plug fitted in its place by an

authorised customer service agent. The replacement plug

should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains

socket elsewhere.

Products sold in AUS and NZ only: Use a residual current

device (RCD) with a rated residual current of 30 mA or

less.

Product Description and Specifica-

tions

Read all safety warnings and all instruc-

tions. Failure to follow the warnings and in-

structions may result in electric shock, fire

and/or serious injury.

Intended Use

The machine is intended for cutting sheet metal without de-

forming the material and is suitable for straight cuts, cut-outs

and narrow curves.

Product Features

The numbering of the product features refers to the illustra-

tion of the machine on the graphics page.

1 On/Off switch

2 Screwed cap for die

3 Locking screw for die

4 Die

5 Punch

6 Hollow screw for fastening of punch

Accessories shown or described are not part of the standard deliv-

ery scope of the product. A complete overview of accessories can

be found in our accessories program.

Bosch Power Tools

Technical Data

Nibbler

Article number

Rated power input

Output power

Stroke rate at no load n

Stroke speed under load

Max. steel sheet cutting capacity*

Cutting width

Smallest curve radius

Weight according to EPTA-

Procedure 01:2014

Protection class

* to 400 N/mm

with reference to steel sheet

The values given are valid for a nominal voltage [U] of 230 V. For differ-

ent voltages and models for specific countries, these values can vary.

Operation

Starting Operation

 Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Switching On and Off

To start the machine, push the On/Off switch 1 forward so

that the "I" is indicated on the switch.

To switch off the machine, push the On/Off switch 1 toward

the rear so that the "0" is indicated on the switch.

Locking/Loosening the Die

For straight cuts, tighten the locking screw 3 using an hex key

(size 2.5 mm) in order to lock the die 4.

For curved cuts, loosen the locking screw 3. The die 4 can

move freely now and adjusts to the direction of the feed

strength.

Working Advice

 Before any work on the machine itself, pull the mains

plug.

 Wear protective gloves while working and pay particu-

lar attention to the mains cable. Sharp burrs develop at

the cut steel sheet and can cause injuries to the operator or

damage the mains cable.

 Exercise caution when handling the cutting chips. The

chips have sharp tips that can cause injuries.

Apply the machine to the workpiece only when switched on.

Always hold the machine vertical to the surface of the steel

sheet and do not tilt it.

The cut takes place during the upward motion of the punch.

Guide the machine evenly and with moderate feed in the cut-

ting direction. A too high feed rate significantly reduces the

service life of the cutting tools and can damage the machine.

English | 5

GNA 2,0

0 601 530 1..

500

270

-1

min

2400

-1

min

1500

2.0

/ II

1 609 92A 37Z | (19.10.16)