Anchor Fiesta Einbauanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Einbauanleitung für Zelt Anchor Fiesta herunter. Anchor Fiesta 4 Seiten. Marquee stair step kit
Auch für Anchor Fiesta: Montageanleitung Handbuch (8 seiten), Montageanleitung Handbuch (9 seiten)

Seite drucken

Instructions

Boxed Stair Step Adapter Kit #8090502

Upright

Adjustable Elbows

Adapters

Short Inserts

Long Inserts

Parts Laid Out by Component Type

1. Assemble (1) Short Insert into each end of (3) Adjustable Elbows (fig.4). The alignment hole is closest to the end of the Short

Insert that connects to the Adjustable Elbow. Partially tighten the set screws, using a 5/16" Allen Wrench.

2. Assemble (1) Long Insert into each end of the (3) remaining Adjustable Elbows (fig.5). Partially tighten set screws, using a 5/16"

Allen Wrench. The alignment hole pattern is closest to the end of the Long Insert that connects with the Adjustable Elbow.

You should now have (3) Short Adapter Assemblies (see Fig.4) and (3) Long Adapter Assemblies (see Fig.5); The (2) Upright

Adapter Assemblies are shipped pre-assembled and will be used later (see fig.9)

Short Adapter Assembly

Rotation Screw. Use

1/4" Allen Wrench

Allen Wrench

Alignment Hole

Short Insert (2)

3. Note: The alignment hole rotation depends upon the location of the part in the Fiesta Marquee frame. The adapters located at the

ridge line of the Marquee will have the alignment holes facing upward in a 90 degree vertical direction. Those adapters located at

the eave line will have the alignment hole rotated 45 degrees to the outside of vertical (left or right, depending upon which side of

the Marquee the part will be. In uneven terrain, it is better to wait until the moment of installation to tighten the alignment holes.

DISTRIBUTION OF ASSEMBLIES THROUGH THE FRAME:

4. Notice that at the Descending Angle of the Marquee (see front cover) there are (2) Short Adapter Assemblies at the Eave (each

side) and (1) Long Adapter at the ridge. At the Ascending Angle of the Marquee, this pattern is reversed. There, there are (2)

Long Adapter Assemblies at the eave (each side) and (1) Short Adapter Assembly at the ridge. At the Inclined Sections, there

are (2) or more Upright Adapter Assemblies (1 per Upright), depending upon the overall length of the incline or stairs.

At this time, the standard Fiesta Marquee frames for the upper and lower levels can be built and positioned. However, the adapter

kit will be easier to install if the uprights (legs) are left off the sections that will join with the Descending and Ascending Angled

frames until after the adapter kit has been installed on those standard frames components.

Installing the Stair Step Kit into standard Fiesta Marquee framing:

FOR SAFETY, EASE AND STABILITY, WE RECOMMEND BUILDING THE FRAME COMPLETE BEFORE INSTALLING THE LEGS

Constructing the Upper Level with Descending Angles (see Fig.6):

5. Position two units of standard Fiesta Marquee framing

(one at the top and one at the bottom of the incline).

6. Starting at either eave of the top unit (Fig.6), pull

the pin holding the eave bar to the Eave Casting and

insert the splice of a Short Adapter Assembly into both

the casting and eave tubing of the Marquee. Rotate the

splice hole into alignment (45 degrees to the outside of

vertical), and replace the pin.

Contents of Stair Step Kit:

Component

Description

Short Insert

Long Insert

Adjustable Elbow

Upright Adapter Assemblies 8090508C

TOOLS REQUIRED: (1) 5/16" Allen Wrench, (1) 1/4" Allen Wrench - - (Tools Not Provided)

NOTE: Only the parts listed in Table 2 are included in this kit. These kit parts are pic-

tured in fig 1 and 3. All other frame parts illustrated in these instructions are stan-

dard Fiesta Marquee components and are not a part of this Stair Step Adaptor Kit.

IT IS ASSUMED THAT THE CUSTOMER ALREADY HAS, OR IS PURCHASING, THE BASIC

FIESTA MARQUEE FRAMES THEMSELVES.

To prepare the Stair Step Kit for installation, assemble the (3) Short and (3) Long

Adapter Assemblies, as shown (fig.4 & 5). In doing this, please note the following

guidelines. Please read all steps before proceeding:

Adjustable

Elbow (1)

Use 5/16"

Inventory

No.

8090505C

8090506C

3551140

Adapter Assemblies:

Long Adapter

Descending Angle

Standard Marquee

Rafters (2)

Table 2

First (2) Bays

Figure

Kit #8090502

No.

(Qty of Parts)

3 & 9

Long Insert (2)

Alignment

Holes

Use 5/16"

Allen Wrench

Assembly

Adjustable Elbow (1)

Ascending Angle

Build from eave-

to-peak-to-eave

Additional Bays

Kit #8090691

(Qty of Parts)