Bosch 23 Original-Bedienungsanleitung - Seite 19
Blättern Sie online oder laden Sie pdf Original-Bedienungsanleitung für Elektrowerkzeug Bosch 23 herunter. Bosch 23 22 Seiten. Angle exact
Auch für Bosch 23: Handbuch für Installation und Nutzung (18 seiten)
Seite drucken
OBJ_BUCH-412-001.book Page 38 Thursday, April 3, 2008 3:18 PM
38 | English
or to adjust the worklight. Adjust the worklight
to the desired position first (see "Adjusting the
LED Worklight", page 38) before adjusting the
angled drive head.
Loosen the lock nut 20 by inserting an appropri-
ate tool into an opening of the lock nut and turn-
ing the lock nut in the direction of the arrow a
(left thread).
Unscrew the angled drive head 3 in arrow direc-
tion b until it can be removed. Unscrew the lock
nut 20 from the motor housing 33 in arrow di-
rection a.
Now, the marking ring can be exchanged or the
worklight can be adjusted.
– Turn the lock nut 20 in arrow direction c onto
the motor housing 33 and screw on the an-
gled screw head again turning in arrow direc-
tion b.
– Lock the angle nutrunner head by screwing
the lock nut 20 in arrow direction c.
– Retighten lock nut 20 again with a tightening
torque of approx. 50 Nm.
Adjusting the LED Worklight (see figure L)
ANGLE EXACT 25 – 250 | 30 – 380 | 40 – 280 |
50 – 210
For these industrial cordless angle wrenches,
the angled screw head must be removed first,
see "Adjusting and Removing the Angled Drive
Head", page 37. Adjust the worklight as de-
scribed below.
ANGLE EXACT 2 | 3 | 6 | 7 | 7 – 900 | 8 |
10 – 650 | 14 – 420 | 14CF | 15 |
17 | 22CF | 23 | 29CF | 30
Press off the marking ring 17 with a thin screw-
driver blade, a knife, or similar. Using snap-ring
pliers, slide the snap ring 34 toward the rear onto
the housing shell. The two shell halves of the LED
holder 16, which enclose the LED worklight 18,
can now be adjusted to any requested position.
Pay attention not to damage the cable of the LED
worklight 35 and slide it into the cavity intended
for it in the housing shell without kinking. En-
close the LED worklight 18 again with the two
housing shells of the LED holder 16. Press the
snap ring 34 and the marking ring 17 back to
their initial positions.
3 609 929 B34 | (3.4.08)
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine (e.g., main-
tenance, tool change, etc.) as well as during
transport and storage, set the rotational di-
rection switch to the centre position. Unin-
tentional actuation of the On/Off switch can
lead to injuries.
For safe and proper working, always keep
the machine and ventilation slots clean.
When the battery is no longer operative, please
refer to an authorised after-sales service agent
for Bosch power tools.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts order,
please always include the 10-digit article
number given on the type plate of the machine.
Power Tool Lubrication
Lubricants:
Special gearbox grease (225 ml)
Article number 3 605 430 009
Molycote grease
SAE 10/SAE 20 engine oil
Clean the gearbox after the first 150 running
hours using a mild solvent. Follow the solvent
manufacturers directions for use and disposal.
Lubricate the gearbox using Bosch gearbox
lube. Repeat the lubrication procedure every
300 hours after the initial gearbox service.
Oil the moving parts of the shut-off clutch after
100000 screwing operations with a few drops of
SAE 10/SAE 20 motor oil. Lubricate the sliding
and rolling parts with Molycote grease. At this
time, inspect the clutch for wear in order to en-
sure that the repeatability and accuracy have
not been affected. Afterwards, the torque of the
clutch must be readjusted.
Have maintenance and repair work per-
formed only by qualified specialists. In this
manner, it can be ensured that the safety of
the power tool is maintained.
Bosch Power Tools