Dreame Vortech Z10 Station Benutzerhandbuch - Seite 12

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Staubsauger Dreame Vortech Z10 Station herunter. Dreame Vortech Z10 Station 13 Seiten.

Seite drucken

Replacing the Battery Pack

The vacuum contains a removable

rechargeable lithium-ion battery pack

which has a limited number of recharge

cycles. After extended use, the battery

pack may no longer hold a charge. If this

happens, it means the battery pack has

reached the end of its life cycle and needs

to be replaced.

1. Press down the battery pack release

button and slide the battery pack to the

right, as illustrated, to remove it.

2. Install the new battery pack.

Fig. E-17

Cleaning the Multi-Surface

Brush

1. Turn the lock counterclockwise until it

stops, then remove the roller from the

roller brush.

2. Use scissors to cut off the hairs and

fibers that get stuck on the brush roller.

Wipe the dust from the notch and

transparent cover with a dry cloth or

paper towel. Thoroughly dry before

use.

3. When it is dirty, rinse the brush roller

with clean water until it is clean.

4. Stand the brush roller upright for at

least 24 hours until it is fully dry.

Fig. E-18-Fig. E-21

Cleaning the Soft Roller Brush

1. As shown in the picture, press the

brush roller release button to remove

the roller from the slot.

2. Use scissors to cut off the hairs and

fibers that get stuck on the brush roller.

Wipe the dust from the notch and

transparent cover with a dry cloth or

paper towel. Thoroughly dry before

use.

3. When it is dirty, rinse the brush roller

with clean water until it is clean.

4. Stand the brush roller upright for at

least 24 hours until it is fully dry.

Fig. E-22-Fig. E-25

Cleaning the Motorized Mini-

Brush

1. Use a coin as illustrated to rotate the

lock counterclockwise until you hear a

click.

2. After unlocking the motorized mini-brush,

remove the brush roller, then rinse and

clean it.

3. Stand the brush roller upright in a well-

ventilated area for at least 24 hours until

it is fully dry.

4. Once the brush roller is dry, reinstall it

by following the disassembly steps in

reverse.

Fig. E-26-Fig. E-29

FAQ

If the vacuum is not working properly, please refer to the table below.

Errors

Possible Causes

The appliance is out of battery or

its battery level is low.

Overheat protection mode

Vacuum does not work.

triggered by a blockage.

The suction opening or air duct is

blocked.

The dust cup is full and/or filter

assembly is clogged.

Weak suction force.

An attachment is blocked.

The motor makes a strange

Main suction opening or

noise.

extension rod is blocked.

The battery indicator is

solid red when charging

Battery pack is damaged.

the vacuum.

The battery indicator blinks

The motor temperature is too

red after turning on the

high. / The bush roller is blocked.

vacuum.

/ The air duct is blocked.

The vacuum is not properly

placed on the dust-removal hub.

The battery indicator

The battery is charged and

does not light up when

switches to Sleep Mode

charging.

automatically.

The problem persists after ruling

out the above two possibilities.

The battery temperature is too

Charging too slow.

low or too high.

LED lights of the multi-

surface brush and

LED lights are damaged.

motorized mini-brush do

not work.

The dust collection bag is

The dust collection status

uninstalled or inappropriately

indicator is solid orange.

installed.

The dust collection status

The dust collection bag reaches

indicator is blinking

capacity or the air duct is

orange.

blocked.

Solutions

Fully charge the vacuum, then resume

use.

Clean the suction opening or air duct.

Wait until the vacuum cools down,

then reactivate it.

Clear any blockage from the suction

opening or air duct.

Empty the dust cup and/or clean the

filter assembly.

Clear any blockage in the attachment.

Clear any blockage in the main suction

opening or extension rod.

Please contact after-sales service for

maintenance.

Check these parts in turn.

Make sure that the charging contacts

of the vacuum is aligned with that of

the dust-removal hub.

The vacuum runs normally.

Please contact the after-sales

department for maintenance.

Wait until the battery temperature

returns normal, and then recharge.

Please contact the after-sales

department for maintenance.

Before dust collecting starts, confirm

that the dust collection bag has been

installed or installed in place.

Replace a new dust collection bag

or clean the air duct. Then press and

hold the dust collection button for 3s

to troubleshoot the problem.