Andis AG Verwendung und Pflege - Seite 2

Blättern Sie online oder laden Sie pdf Verwendung und Pflege für Haarschneidemaschine Andis AG herunter. Andis AG 2 Seiten. Detachable plus model ag clipper detachable blades are compatible with oster model a5
Auch für Andis AG: Teileliste (1 seiten), Spezifikation (2 seiten), Benutzerhandbuch (2 seiten)

Seite drucken

impORtant safegUaRds

When using an electrical appliance, basic precautions

should always be followed, including the following:

Read all instructions before using the Andis Clipper.

dangeR:

to reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into

water. Unplug immediately.

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it can fall or be

pulled into a tub or sink. Do not place in or drop into

water or other liquid.

4. Always unplug this appliance from the electrical outlet

immediately after using.

5. Unplug this appliance before cleaning, removing or

assembling parts.

waRning:

to reduce the risk of burns, fire

electric shock, or injury to persons:

An appliance should never be left unattended when

plugged in.

Close supervision is necessary when this appliance is

used by, on or near children or individuals with certain

disabilities.

Use this appliance only for its intended use as

described in this manual. Do not use attachments not

recommended by Andis.

Never operate this appliance if it has a damaged cord

or plug, if it is not working properly, if it has been

dropped or damaged, or dropped into water. Return the

appliance to an Andis Service Center for examination

and repair.

Keep the cord away from heated surfaces.

Never drop or insert any object into any opening.

Do not use outdoors or operate with aerosol (spray)

products are being used or where

oxygen is being administered.

Do not use this appliance with a damaged comb or

broken blade, as injury to the skin may occur.

To disconnect turn control to "off" then remove plug

from outlet.

10. WARNING: During use, do not place or leave appliance

where it may be (1) damaged by an animal or (2)

exposed to weather.

saVe these instRUctiOns

this product is intended for commercial Use

seRVicing Of a dOUble-insUlated clippeR

In a double-insulated clipper, two systems of insulation are

provided instead of grounding. No grounding means is pro-

vided on a double-insulated clipper, nor should a means for

grounding be added. Servicing a double-insulated clipper

requires extreme care and knowledge of the system, and

should be done only by an Andis Authorized Service Station.

Replacement parts must be identical to those parts being

replaced. A double-insulated clipper is marked by the words

"DOUBLE INSULATION" or "DOUBLE INSULATED". The

symbol

may also be marked on the appliance.

OpeRating instRUctiOns

Please read the following instructions before using your new

Andis Trimmer. Give it the care that a fine precision built instru-

ment deserves and it will give you years of service. before

starting your clipper remove the blade guard (some models

may not have a blade guard). Plug cord into electrical outlet,

operate 120 volt, 60 cycle AC electrical current or as noted on

unit. To start clipper move switch button to on position, to

stop, move switch button back to original position. After using

your Andis Clipper, rewrap cord, and store in a safe place.

RemOVing blade set

To remove blade set, first

make sure your clipper

motor is switched off,

then push down on blade

with both thumbs

(Diagram A) and slide

blade off blade hinge. If

your blade hinge should

snap closed and is flush

with the clipper, use a

small standard screw-

driver to pry the tongue

of the hinge out

(Diagram B).

nOte: Hair may accumu-

late in the front cavity of

the housing under the

blade. If this happens,

you can clean out the

hair by brushing out the

cavity with a small brush

or an old toothbrush

while the blade is off the

clipper (See Diagram B

for location of cavity

being referenced).

Replacing OR changing blade set

To replace or change your blade set, slide the blade bracket

onto the hinge of the clipper (Diagram C) and with the clip-

per turned on, push the blade towards the clipper to lock

into position.

UseR maintenance

The internal mechanism of your motor clipper has been

permanently lubricated at the factory. Other than the recom-

mended maintenance described in this manual, no other

maintenance should be performed, except by Andis

Company or an Andis Authorized Repair Service Station.

caRe and seRVicing Of yOUR andis clippeR blades

Blades should be oiled

OIL

before, during, and after

use. If your clipper

blades leave streaks or

slow down, it's a sure

OIL

sign blades need oil.

Place a few drops of

Andis Clipper Oil on

the front and side of

DIAGRAM D

the cutter blades

(Diagram D). Wipe excess oil off blades with a soft dry

cloth. Spray lubricants contain insufficient oil for good lubri-

cation, but are an excellent clipper blade coolant. Always

replace broken or nicked blades to prevent injury. You can

clean the excess hair from your blades by using a small

brush or worn out toothbrush.

To clean the blades we

suggest to immerse the

blades only into a

shallow pan of Andis

Clipper Oil, while the

clipper is running. Any

excess hair and dirt that

has accumulated between

the blades should come

DIAGRAM E

out. After cleaning, turn

your clipper off and dry blades with a clean dry cloth and

start clipping again. If upon cleaning your blades you find

that the blades will still not cut, there may be a few fine

pieces of hair trapped between the upper and lower blade. If

this happens, you will need to snap the blade off the clipper.

Proceed to slide the upper blade to one side, without loos-

ening the tension spring or moving the upper blade com-

pletely out from under the tension spring (See Diagram E

for position of blade). Wipe the surface between the blades

clean with a dry cloth, then place a drop of clipper oil where

the upper and lower blades meet and also in the guide slot

of the tension spring (Diagram E). Now slide the upper

blade to the opposite side of the lower blade and repeat this

process. After completing this cleaning procedure, slide the

upper blade centering it over the lower blade. Handle or

store your Andis Clipper with the blades down so excess oil

will not run into the clipper case.

caUtiOn: Never handle your Andis clipper while you are

operating a water faucet or in water. There is danger of

electrical shock and damage to your clipper. andis

cOmpany will not be responsible in case of injury due

to this carelessness.

Replacement Of caRbOn bRUshes

waRning: clipper must

be unplugged before

removing carbon brush

caps or performing any

maintenance, as electri-

cal shock may occur.

The carbon brushes of

your clipper should be

checked every three to

DIAGRAM F

OIL

six months. Carbon brush replacement should be performed

when the carbon brushes reach no less than 1/16" in length.

To replace the carbon brushes, unscrew brush caps with a

standard screwdriver. Do one side at a time.

caution: The carbon brushes are spring loaded. Take pre-

caution when unscrewing the brush caps from the unit

(Diagram F). The brush spring should be in plain view upon

removing the cap. Pull out the spring and brush from its

canal, then remove old carbon brush. Tip the clipper to one

side so the carbon brush slides out. Be sure to note the way

the brush is inserted so that if it does not need replacing, it

may be re-inserted in exactly the same position.

TOP OF CLIPPER

CARBON BRUSH CANAL

CARBON BRUSH

INSERT BEVEL SIDE FIRST

BEVEL

DIAGRAM G

When placing a new carbon brush into the carbon brush

canal, make sure to align the curvature on the end of the

carbon brush with the curve of the commutator seen at the

bottom of the canal (Diagram G). When aligned properly, the

two beveled edges of the carbon brush will be located in the

upper right and lower left corners. Be sure to insert the bev-

eled end of the carbon brush into the canal first. Failure to

perform this procedure correctly may cause the carbon

brushes to not seat themselves properly against the com-

mutator. Replace the carbon brush spring into the brush

cavity after the carbon brush has been installed, then

replace carbon brush cap with a standard size screwdriver.

Turn clockwise only until you feel the brush cap stop. If the

brush cap is tightened too tightly, it will force the brush

spring past the carbon brush and will cause damage to the

commutator.

CAP

SPRING