Andis 19SL410U Handbuch

Blättern Sie online oder laden Sie pdf Handbuch für Trimmer Andis 19SL410U herunter. Andis 19SL410U 2 Seiten. Andis company clipper/ trimmer manual

Seite drucken

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions

should always be followed, including the following:

Read all instructions before using the Andis clipper/

trimmer.

DANGER:

To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into

water. Unplug immediately.

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it can fall or

be pulled into a tub or sink. Do not place in or drop

into water or other liquid.

4. Always unplug this appliance from the electrical

outlet immediately after using.

5. Unplug this appliance before cleaning, removing or

assembling parts.

WARNING:

To reduce the risk of burns,

fire electric shock, or injury to persons:

1. An appliance should never be left unattended when

plugged in.

2. Close supervision is necessary when this appliance

is used by, on or near children or invalids.

3. Use this appliance only for its intended use as

described in this manual. Do not use attachments

not recommended by Andis.

4. Never operate this appliance if it has a damaged

cord or plug, if it is not working properly, if it has

been dropped or damaged, or dropped into water.

Return the appliance to an Andis Service Center for

examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any opening.

7. Do not use outdoors or operate with aerosol (spray)

products are being used or where oxygen is being

administered.

8. Do not use this appliance with a damaged or broken

blade, as injury to the skin may occur.

9. To disconnect turn control to "off" then remove plug

from outlet.

10. If this clipper/trimmer has means for grounding,

connect to a properly grounded outlet only.

See Grounding Instructions.

11. If used as an animal clipper/trimmer or shear:

during use, do not place or leave appliance where it

may be (1) damaged by an animal or (2) exposed to

the weather.

THIS PRODUCT INTENDED FOR PROFESSIONAL USE

SAVE THESE INSTRUCTIONS

OPERATING INSTRUCTIONS

Please read the following instructions before using your

new Andis cordless clipper/trimmer. Give it the care that

a fine precision built instrument deserves and it will give

you years of service.

READ THE FOLLOWING BEFORE CHARGING THIS

CLIPPER/TRIMMER

Remove Andis clipper/trimmer and charger from carton

and plug into 120V or 230V outlet as identified on the

bottom of the charger, or on the outside of the carton.

Note that the clipper/trimmer ON/OFF switch must be in

the OFF position for the battery to charge. Place

cordless clipper/trimmer into form fitting pocket in

charger. The unit is "keyed" to fit one way only. The

green light on the charger will turn on. The

clipper/trimmer has electrical contacts that touch

electrical contacts in the charger. The weight of the unit

will give sufficient contact. The clipper/trimmer is not

charged at the factory. Please recharge clipper /trimmer

for 12 hours (overnight) before first use for maximum

performance.

You may keep the clipper/trimmer in the charger when

not in use. The charger will maintain the battery at full

charge and the green light will stay on. The unit has a

Nickel Metal Hydride battery that cannot be damaged by

overcharging. However, we recommend that the charger

be unplugged if the clipper/trimmer won't be used for

seven or more days.

PLEASE NOTE: Nickel Metal Hydride batteries have

less "Memory Effect" than Nickel Cadmium batteries.

Memory Effect is caused by repeated short uses of the

clipper/trimmer, followed by charging. The battery never

fully discharges and, therefore, "forgets" how much

energy it can store. In order to maximize the

performance of your Nickel Metal Hydride battery, please

follow these steps:

1) Oil blade. Turn clipper/trimmer on and allow it run until

the blade slows significantly. It is not necessary to let

the blade stop completely.

2) Turn clipper/trimmer off. Charge overnight.

3) Conduct the above exercise every sixty days.

FAILURE TO CHARGE:

1) Make sure voltage is present at the wall outlet

(confirm with an appliance you know is working).

2) Check the alignment of the contacts between the

clipper/trimmer and those in the charger. The contacts

in the charger should be centered in the small

openings, and protrude slightly into the charger

pocket. Disconnect power to the charger, and correct

if necessary.

3) Make sure contacts on both charger and

clipper/trimmer are clean. Disconnect power to the

charger and rub contacts with a pencil eraser until

shiny. Wipe contacts and brush off remaining dust with

a soft dry cloth.

4. If failure to charge still exists, return trimmer to Andis

or an Andis Authorized Service Station listed in this

manual for examination and repair or replacement.

ATTENTION: The product you have

purchased contains a rechargeable battery.

The battery is recyclable. At the end of its

useful life, under various state and local

laws, it may be illegal to dispose of this

battery into the municipal waste stream. Check with your

local solid waste officials (or call 1-800-822-8837) for

details in your area for recycling options or proper

disposal.

USER MAINTENANCE

The internal mechanism of your clipper/trimmer has been

permanently lubricated at the factory. Other than the

recommended maintenance described in this manual, no

other maintenance should be performed, except by

Andis Company or an Andis Authorized Repair Service

Station.

CARE AND SERVICING OF YOUR ANDIS TRIMMER

BLADES- (Trimmer shown in diagrams may vary to

the one that you have.)

Blades should be

oiled before,

during, and after

each use. If your

trimmer blades

leave streaks or

slow down, it's a

sure sign blades

Diagram A

need oil. The

clipper/trimmer should be

OIL

held in a position shown in

Diagram A to prevent oil

from getting into motor.

Place a few drops of Andis

OIL

Clipper Oil on the front and

side of the cutter blades

(See Diagram B). Wipe

excess oil off blades with a

soft dry cloth. Spray

lubricants contain

Diagram B

insufficient oil for good

lubrication, but are an excellent clipper coolant. Always

replace broken or nicked blades to prevent injury. You

can clean the excess hair from your blades by using a

small brush or worn out tooth brush. To clean the

blades we suggest to immerse the blades only into a

shallow pan of Andis Clipper Oil, while the clipper is

running. Any excess hair and dirt that has accumulated

between the blades should come out. After cleaning,

turn your clipper/trimmer off and dry blades with a dry

cloth and start clipping again.

REPLACEMENT (REMOVAL) OF BLADE SET

Your Andis clipper/trimmer

consists of a preset

tension assembly on the

blade set. To remove

blade set from your

clipper/trimmer, remove

from charger base. Turn

the clipper/trimmer upside

down so teeth of blades

BLADE SCREWS

are facing down. You may

wish to set the clipper on a

Diagram C

flat surface while

performing these operations. Using a phillips type

screwdriver, unscrew the two blade screws as shown in

Diagram C. Remove blade set from clipper/trimmer.

Install new blade set, making sure the blade yoke

cradles the armature pin on clipper/trimmer (See

Diagram D). There is no need to adjust blade tension

before use, as tension has been preset at the factory.

Align screw holes of blade set to screw inserts on

clipper/trimmer housing. Replace the screws. Before

tightening down blade screws, check alignment of

blade set to housing, making sure that they are parallel.

Tighten down screws.

ARMATURE

BLADE

YOKE

Diagram D

OIL

STAINLESS